Jump to content
SAU Community

Recommended Posts

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I'm interested in the front disc rotors. what's their current thickness? do you have the lines from the front callipers as well?

can pick up this sunday if suitable. please call my mobile to work out a deal.

Justin...

0418663628

Could u send pics of inside door trim drivers side, i only require the pocket and surround if u can seperate excellent if not ill buy the whole thing!

Also pics of catch can.

If u Still Have Both Is Pick-up Availble For Anzac Day?

[email protected]

Thanks

Hi, I’m after a Rear Left small plastic side skirt (glues to base of rear quarter panel).. would you have one by any chance? thank you

i have a pair not factory think they are GTR style $150.00

I'm interested in the front disc rotors. what's their current thickness? do you have the lines from the front callipers as well?

can pick up this sunday if suitable. please call my mobile to work out a deal.

Justin...

0418663628

they are 28mm..sorry for delay have been away..lines gone..if still interested 0417295636.

thanks

Could u send pics of inside door trim drivers side, i only require the pocket and surround if u can seperate excellent if not ill buy the whole thing!

Also pics of catch can.

If u Still Have Both Is Pick-up Availble For Anzac Day?

[email protected]

Thanks

sorry dont have drivers trim..catch can is behind pipe in the picture attached and pick up anzac day in morning fine with me.

post-3004-1145792638.jpg

do you have the plastic trim that goes around the manual gearbox and the ash tray?

i still have it although it has a crack in it and is painted blue..can be repaired and painted. Can have it for $20 including post if needed with ashtray as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...