Jump to content
SAU Community

Recommended Posts

I realise there are many various types available,

are there any atmo's that don't cause the car to stall, etc, etc

In Short No.

The lack of air on the intake IS the reason why it stalls.

Throw a pod on and it'll make a sound.

or

Block off the stock BOV with a pod andf it'll make a cooler sound.

or

Forget about sound and concentrate on other things like CAI, Hi Flow CATS and FMIC.

Moot

No benefit.

Much the same way as there is no benefit with running a atmo BOV. How about you tell us why you want a atmo bov?

If it's for something other than then rice factor then perhaps we can collectively think of another solution for your untold troubles.

Moot

the only way to make the stock bov vent to atmo properly is to get a one way valve on to the venting end.

this can be done.

if you really want to, measure the OD of the bov outlet then go to a plumbing store with those measurements and look for a one way valve to fit over that OD. so on idle when the bov is open, air will not be sucked in from there.

NOTE: this will alow you to get the sound you want but it doesn't prevent the running rich and so forth..

The car came with the atmo BOV on it, just trying to work out whats better.

I see....

So why do you want to turn a stock BOV (which you don't have) into an atmo one?

Trust me...the stock one is loud!!!! If you wanna make it louder then get a metal intake pipe.

The stock one is ten times better on a stock ECU. If you get a power FC then go atmo all the way

End of Story.

it would be very silly to change to a map sensor ecu just for a stupid BOV.

but yes it would work a bit better. you cannot get djetro rb20 but you can get an rb26 djetro working on an rb20 to achieve the same goal

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...