Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...
  • 2 years later...

i have a r33 diff ready to go into my r32.

since i havent put it in yet, i am not 100% sure about this but this is what ive done so far

swap the backing plate off the r32 diff (4 bolt cover) onto the r33 diff. the r33 diff has a 2 bolt backing plate which wont fit your r32 subframe.

the front two diff bolt loops (near the main driveshaft) are a lot larger on the r33 diff. so you will need some bushings and longer bolts to accommodate the bushings to fit the r32 subframe.

other than that i think it should fit

they are both r200 diffs and should both have the 5x1 bolt axle pattern.

  • 1 year later...

Hi guys,

sorry for revitalizing this topic.

There is someone who wants to swap his R33 2way diff with my r32 OEM diff. Will it fit plug and play? I read the posts above but I'm not 100 % sure about clip14s post. Do I have to switsh the whole diff, with back plates etc. or is there a possibility just to fit the inner part of the diff into the housing?

For example putting this :

KAAZ-Toyota-2-way-LSD-DAT3020_1312.jpg

into this :

truck-differential.jpg

(Those are just example pictures to show you guys what I mean)

I hope you can help me out.

Cheers Dom

Don't think 33gtst is 6 bolt.. GTR is 6 bolt and S13 is also 6 bolt but in a 3x2 config.

I'm also pretty sure that R33 crown wheel bolts are 12mm where R32 is 10mm. Which is why I ended up going for an S13 centre.

  • 2 weeks later...
Don't think 33gtst is 6 bolt.. GTR is 6 bolt and S13 is also 6 bolt but in a 3x2 config.

I'm also pretty sure that R33 crown wheel bolts are 12mm where R32 is 10mm. Which is why I ended up going for an S13 centre.

wont matter what size the crown wheel bolts are if you are replacing the whole diff centre

  • 1 month later...
  • 2 months later...
  • 1 month later...

crown wheel and pinion are matched. you are not meant to put and existing center ( with a random crown gear) into a different housing because the pinion and the crown wheel wont be a matched pair. u can swap pinion drive if u like but u need a press.

running unmatched crown and pinion can cause them to eat the case hardening off each other and at the least be noisy.

the 32 subframe accepts the 4 bolt housing cover from the r32 r200 diff

the 33 r200 diff has a 2 bolt housing cover to suit the r33 subframe.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...