Jump to content
SAU Community

R33 Thermostat


Recommended Posts

Guy's follow the bottom radiator hose up to where it joins the motor,,,thats the stat cover,,,3 bolts from memory.

The stat is the same as a VL 3.0L,,,Nissan Part No is 21200-42L05 and it fits all R33's.

Neil.

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-195749
Share on other sites

  • 6 years later...

ok guys, there are a few things to know here:

firstly for the money and time saving just get a genuine nissan one from nissan parts. they are around $50-60.

second, if you want a 'tridon' one...the part number is TT268-170. this is the 77deg one. there is an 85 deg one...dont get this!

lastly if you want to waste money, get the nismo one but these are over $100 if not closer to $150 and open at 67 or so deg.

you will also need gasket goo for this as there is not a norml gasket there. i use the blue stuff...works perfect!

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4606827
Share on other sites

bellow i attached instructions from the RB engine manual.

view order 3 then 1 then 2. (sorry i didnt rename)

as the above people have said use either the tridon or stnd nissan one.

tridon will set you back about $28 and its one of the good cheapies.

make sure the jiggle pin is pointing to the top of the motor.

for gasket sealent i recomend a product from loctight.

Its a silicone based gasket goo, its loctight blue something or other.

It's the ducks nuts, will come in handy down the track to.

let us know how you go.

post-55273-1242824646_thumb.jpg

post-55273-1242824666_thumb.jpg

post-55273-1242824704_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4606908
Share on other sites

was reading a thread recently and a workshop operator said he'd been through a bunch of tridon thermostats that were crap, and caused problems.

just use the nissan one. also there is no reason to use a lower temperature it will NOT help you, it just means your car won't get up to temp and you'll lose fuel efficiency.

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4608777
Share on other sites

  • 2 years later...

hi guys on my r33 gtst 1993 it has a braided cable that runs down threw the chassis and comes out next to the exhaust, and theres something that attaches to that which im not sure what it is or where to get another one because i scraped going over a speed hump and its pulled it out and stuffed it and i think its shorting out, my thermostat light is staying on and check engine also comes on itermitently. Any help on where i can get another one of these, and or what it is would be good cheers

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-6110663
Share on other sites

  • 2 years later...
hi guys on my r33 gtst 1993 it has a braided cable that runs down threw the chassis and comes out next to the exhaust, and theres something that attaches to that which im not sure what it is or where to get another one because i scraped going over a speed hump and its pulled it out and stuffed it and i think its shorting out, my thermostat light is staying on and check engine also comes on itermitently. Any help on where i can get another one of these, and or what it is would be good cheers

Disconnect it, it's useless. Pull out your passenger seat and delete that sensor

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-7274366
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What Duncan said sounds right. Also, it looks like they only have the driver's mat. Not the rest. Because looking at the diagram: KG4911 is just the mat for the driver. KG4900 is the full set if I'm not mistaken and discontinued.   But, it looks like they may still have the full set for the manual S2. Might be worth checking for the other models as well as they seem slightly different. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/misc/G49 Man, I'm tempted.
    • I dunno about that as a blanket statement. Pitwork is Nissan's "Nissan genuine" thing, and for stuff like timing belts, I have found them to be excellent. Of course, for things like oil filters, you always use proper trusted brands anyway, not whatever the OEM has taken to using.
    • Ahhhh... If you were putting 12V to the led in there, that's likely made it very unhappy. Chances are how you put power, was 12V across an LED that's meant to only have about 20mA through it at peak, and a forward voltage of about 1.8 to 2.4 volts. That circuit is likely only a 3V3 circuit, and will have a resistor in series with the led too. That's my guesstimate on that light, without having touched one.
    • Another vote for installing them and see how you go.  I mean, you already own them, why would you not fit them? 
    • I have had too many of those over the years, my cars have a toolkit or at minimum a cheapy multi tool thing because its too easy to be snookered by some stupid plastic clip that stops you checking the battery terminal isn't loose.
×
×
  • Create New...