Jump to content
SAU Community

Recommended Posts

Hi Guys,

Well I'm about to put some major K's on the car and figured I better change a few things now rather than later, however stuck with a dilemma when it comes to part numbers. Unfortunately Repco has the attitude that they wont help you if you own a Skyline more recent than '91 .....

Basically just after Part #'s for the following items, if available even suppliers who carry would be fantastic.

All parts needed are for a 1996 R33 GTS-T (RB25DET)

* Fuel Filter (have done a bit of a search and found three answers so far being a Ryco z200, z201 or z387, can anyone confirm the correct choice ?)

* Oil Filter (advised of Ryco z145 or z145a, once again need confirmation)

* Timing Belt (no idea)

* Water Pump (no idea)

* Thermostat (no idea)

* Spark Plugs (thinking either NGK BPR6ES or BCPR7ES however not sure if 6 or 7 heat range is better, both gapped at 0.8)

Any help is greatly appreciated. It would be good if accumulated could put as a sticky thread for reference when doing maintenance.

Also feel free to add any other part #'s of items you may know of that I havn't listed here, the more the merryier. Just list the details of the part and part number (also if it's a genuine nissan part or something like a Ryco filter etc)

Cheers !!

Link to comment
https://www.sau.com.au/forums/topic/11325-part-numbers-any-help-appreciated/
Share on other sites

For the fuel filters, it is either z200 or z201. I'm 99% sure it is z201. Just go into repco, autobarn, whatever and check em out both.... Look at yours first as a pint of comparison....

ALSO, I just remembered, there was a difference b/w the 2 that will help figure out whick one...

The correct one has these types of inlets / outlets..

................ ---

................/....

.................|..|

.................|..|

...........--------------

...........|................|

...........|................|

Whereas the other had a different type.

Hope this helps...

genuine nissan numbers for rb25det

oil filter:same as VL RB30

timing belt:13028-20p25

water pump:21010-21u25 (also same as vl rb30)

a/c belt:11720-77a00

alternator belt:11720-42L01

p/s belt:11950-58s01

fuel filter i used z202

after market belt numbers from bosch

a/c belt:4pk910

alt belt:4pk850

p/s belt:3pk345

(alot cheaper)

for the spark plugs do a search and read the threads to make up ur own mind on wheather u want platinums or not. i got platinums but only cause i got then for free.

u will also find variouse part numbers for different brands when researching the plugs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...