Jump to content
SAU Community

Recommended Posts

Got some near new (6000kms) HKS Hypermax II coilovers. Height and damper adjustable, immaculate condition. Straight bolt-in to R34 Skylines. (Piece of cake install, 1 hour for a set or so)

$1650 obo

In South Australia, PM or phone me 041 393 1027 - I can organise freight interstate.

coils1.jpg

coils2.jpg

Edited by Scrub
Link to comment
https://www.sau.com.au/forums/topic/113443-h-k-s-hypermax-coils-for-sale/
Share on other sites

They will not fit R32 GTR as the rear shockers are actually taller on R33GTST, R33GTR, R34GTT & R34GTR as compared to the shockers on R32GTST & R32GTR

Also the the only difference between this GTR setup up and a GTST/GTT setup

is the ball joints are on front only as compared to GTST setup having ball joints on all four.

someone correct me if im wrong but that is my understanding... :D

  • 4 weeks later...
**Bump** - Sale fell through :|

R33 GTST/GTR & R34GTT/GTR are the models they fit!

Sorry but no they they won't fit R33GTST

They will only fit R33GTR, R34GTT and R34GTR and Stagea 260RS

I had them in my R34 GT-T, only reason Im selling is because I have 19" wheels and I have to set too much preload to fit them in.

That’s how you adjust the height, wind up the lower spring seat.

Preload out of the car is irrelevant, it has no effect on the spring rate. The springs are always “preloaded” when they take up the static weight of the car anyway.

Wheel diameter is equally irrelevant, you would have used lower profile tyres so that the total diameter (wheel and tyre) are the same. Otherwise you will have speedo error.

:D cheers :worship:

Edited by Sydneykid
Sorry but no they they won't fit R33GTST

They will only fit R33GTR, R34GTT and R34GTR and Stagea 260RS

That’s how you adjust the height, wind up the lower spring seat.

Preload out of the car is irrelevant, it has no effect on the spring rate. The springs are always “preloaded” when they take up the static weight of the car anyway.

Wheel diameter is equally irrelevant, you would have used lower profile tyres so that the total diameter (wheel and tyre) are the same. Otherwise you will have speedo error.

:dry: cheers :(

... so any serious enquiries of purchase?

I have been told they'll fit R33 GT-T/GTR by the HKS dealer, I've heard a lot of to-ing and fro-ing.. But only real enquiries, we've had everyone's two cents worth.. thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...