Jump to content
SAU Community

Series 4 Mazda Rx7 Savanna (300hp+ At Wheels)

dsi-styl
 Share

Recommended Posts

dsi-styl Newbie

dsi-styl

Posted
Posted

For sale or swap Mazda Rx7 Series 4 Savanna

The vehicle is in immaculate condition in and out it has all your usual factory electric options , sunroof etc . Though the engine side of it has a alot of goodies , its 13bt , custom front mount cooler , custom 3" cooler pipng , 1000cc rochestor secondary injectors , 800cc primary injectors , malpassi fuel pressure reg , 600hp bosch 044 fuel pump , microtech mtx-8 with handset controller , big high flow series 5 turbo by gcg turbochargers 300hp at wheels on low 10psi it also has 18" wheels a full custom 3" turbo back exhaust system 2 cannon mufllers , boost gauge , turbo timer , 16" thermo fan etc ....

interested in swap for nissan 200sx s14 or something of interest as its my only car and realised that i need deeper pockets to fuel the 13bt for everyday driving make an offer

no pictures available

if interested contact kalvin on 0431262773 or pm me

im in sydney and the car can be shipped at buyers expense unless otherwise

jasv35 Explorer

jasv35

Posted
Posted
For sale or swap Mazda Rx7 Series 4 Savanna

The vehicle is in immaculate condition in and out it has all your usual factory electric options , sunroof etc . Though the engine side of it has a alot of goodies , its 13bt , custom front mount cooler , custom 3" cooler pipng , 1000cc rochestor secondary injectors , 800cc primary injectors , malpassi fuel pressure reg , 600hp bosch 044 fuel pump , microtech mtx-8 with handset controller , big high flow series 5 turbo by gcg turbochargers 300hp at wheels on low 10psi it also has 18" wheels a full custom 3" turbo back exhaust system 2 cannon mufllers , boost gauge , turbo timer , 16" thermo fan etc ....

interested in swap for nissan 200sx s14 or something of interest as its my only car and realised that i need deeper pockets to fuel the 13bt for everyday driving make an offer

no pictures available

if interested contact kalvin on 0431262773 or pm me

im in sydney and the car can be shipped at buyers expense unless otherwise

hey pic's please?

you willing to swap plus cash?

  • 2 weeks later...
  • 2 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...