Jump to content
SAU Community

Recommended Posts

With turbo engines the oil is "abused" more, as it is used as a cooling fluid, thus is subjected to greater heat, which can break down the oil faster.

I have never owned a new turbo car so i have never seen the owners manual, but i would be extremely surprised is any manufacturer would recommend service intervals of less than 10,000km. At the end of the day they are only concerned about the car lasting for the duration of the "manufacturer's warrenty".

I get mine serviced at every 10,000kms but i dont have any mods or anything. If i had some mods i'd get it serviced at every 5,000km.

Theres a decal under the bonnet that tells u most things like when u should change the air filter, oil and filter, fuel filter and what the gap size in the spark plugs should be.

I'm not saying you should do exactly what it says but use it as a guide line

Well i check my oil regulary, and will stick with 10,000 service intervals (that includes oil filter) and looking at the oil in there at the moment been in about 4000 k's and looks not to bad to me. Definietly not like new but not like soot either.

I am constantly amazed that people think 10-15 year old cars have done less then 100,000 km.

Dont you mean less than 30,000 ? Plenty 10 yo cars in Japan with less than 100,000 but they dont come here, we mostly get higher k's cars here .

yeah plenty with their Speedo’s wound back anyway.

Im sure truely by now if you have/are going to import a car with low kms you would suspect that its speedo's might have been tampered with. Mostly people just turn a blindeye or ignore the speedo's readings. There are other ways to check the condition of the car like the condition of its interior (low kms+worn seats, steering wheel etc = speedo's been tampared with). You can also check the engine of the car (find a sticker where it state when the timing belt has been changed etc). Like most people have said in the above posts its not that hard to change electronic odometers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...