Jump to content
SAU Community

Recommended Posts

hey ALL.

quick question due to expencive fuel price, my car is alway on boost. do i have to do any thing if i turn my boost conrtoler down to say 4psi, another word mostly on vac. its a light modded car with standard ecu.

thanks

depends, is it a stock turbo? the only way to get it to boost so low would be to disconnect the wastegate actuator, and jam the gate fully open. if left connected, it will boost to a minimum of the wastegate actuator spring rate.

Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2105738
Share on other sites

r33 s1, stock ecu,stock turbo, 3"inch cat back zost, pod, 11pis boost.the car does move unless i tap it abit harder but then its in boost so i back of. wat i meant to say was. do i have to reset ecu, regap spark plugss or thins like that if i turn boost down really low until petrol price drop a little. i get 400ks with 50-55 litres when i fill up.

Edited by bluer33
Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2105799
Share on other sites

400km is pretty good though

umm main things to check are the O2 sensor in the exhaust can cause worse economy..

turn the boost back to std 7psi at least.. actuator will allow this..

try a reset on the ecu, also check it for error codes..

Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2105838
Share on other sites

speaking of resetting the ecu, should you reset it when you turn up your boost?

i turned mine up to 10 psi from 4 ..

Im also getting 450kms per tank with 10 psi.. (which seems to be pretty good) ..

Cheers,

-JD

thats what i usedto get at 50km trips each way to and from work..

on 11 psi.. but a fair bit of cruising

currently getting about 13L/100kms with 294rwkw.. so needs a light load tune redone.

Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2105858
Share on other sites

Exactly. You get more boost the more you put your foot down. Just keep the revs lower (dont change above 3000rpm), don't warm up the car longer than 30 sec, anticipating red lights, steady and smooth accelerator control etc can all help.

Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2105970
Share on other sites

lol i love ... untill the fuel prices go down? WE ARE GOING TO GET KILLED BY FUEL PRICES .... it wont go down it will only go up. I payed 1.40 a litre the other day.. when you pay more for a litre of fuel then you do for a litre of milk you know its absolute bullshit. In the few years i have been driving it has gone up almost 60 cents a litre.

Edited by fEkuaR
Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2105992
Share on other sites

paul,

have noticed that the closed loop on the power FC doesn't seem as good as on the std ecu.

when cruising it

A) doesn't bounce the AFR guage as much

B) only seems to do it when slightly accelerating and sits within stoich while holding the throttle in one spot.

C) when holding the throttle in one spot and its not bouncing, increased load on the engine (say a slight hill) it will start working.

not that its running too bad, im at 300km and 1/3 tank left.

Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2106473
Share on other sites

paul,

have noticed that the closed loop on the power FC doesn't seem as good as on the std ecu.

when cruising it

A) doesn't bounce the AFR guage as much

B) only seems to do it when slightly accelerating and sits within stoich while holding the throttle in one spot.

C) when holding the throttle in one spot and its not bouncing, increased load on the engine (say a slight hill) it will start working.

not that its running too bad, im at 300km and 1/3 tank left.

i noticed this too!!!! maybe we should tune the ecu lean and then turn off closed loop mode ?

Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2106889
Share on other sites

The fuel injection map in the ECU is based on airflow load and RPM.

It has nothing to do with boost pressure

boost affects airflow though...

if you wish to turn boost down, unplug the factory boost solenoid and unplug any other boost controller. that way, it will read about 5psi and will never go into 'high' mode.

Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2106982
Share on other sites

whilst you are correct, the throttle pedal decides the final factor.

sure if you run 10psi and full throttle it, its going to chew through lots more air. but thats the throttles fault i would expect (ie: the driver) and not turbocharger boost pressure

Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2106996
Share on other sites

I've noticed that the closed loop on the PowerFC is pretty good. Cruising, accelerating lightly, idling etc, my wideband is always reporting a stoich AFR. I guess it comes down to how close your base map is to stoich! (and the condition of the factory O2 sensor)

Edited by Busky2k
Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2108612
Share on other sites

closed loop should be bouncing the AFR's from lean to stoich.

i think its like 10 times per minute or something, not just sitting in the stoich area on the guage..

i think the condition affects how responsive the unit is.

Bluer33 - safc would allow you to tune the ECU beter for more economy as the std maps are fairly rich when your giving it to the car..

gaps would only help if they are wrong and not the correct gap.. most people run 0.8 for under 1bar of boost.

dont think a dump would help economy too much, except that it would help with power, so less throttle to do the same as before.. so yes it might, as long as your right foot is in check.

Edited by Craved
Link to comment
https://www.sau.com.au/forums/topic/114308-petrol-price/#findComment-2108663
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah, nothing formal, just open track days. Mostly small and tight circuits but I would like to get back out to Eastern Creek at some stage.
    • What type of track driving will you be doing?  Do you have a set of class rules you need to abide by that will limit your rim / tyre width?
    • I've been reading a lot lately about unsprung weight and how beneficial it can be to reduce it for driving on the track, given my semi's only have another day or two in them I am throwing around the idea of some lighter wheels and a square set up. I have 265/35/19's and 245/40(?)/19 Federal 595's at the moment. The wheels and tyres are super heavy. I looked up my wheel weight online and got 14.5kg naked. Not sure if this was 8.5 (front) or 9 (rear) but that's a lot. I have also been reading about the benefits of a square setup. Much better rotation and potentially less understeer.  When I throw these together I'm thinking about a 17x9 or 18x9 square (preferably under 10kgs per wheel) with 245 or 255's. I can get some cheap 17x8.5 BMW M Sport wheels, they weight 10.5 kg's each but at 8.5 wide could probably only get 245's on them? I know they come with 255's from factory but semi's are a bit chunkier. Otherwise it will be aftermarket wheels in a 9" width. Most of the other BMW wheels are heavy unless you pay a squillion dollars for some M wheels.  Although, the E46 M3 Style 67's could be good but I'd have to buy 2 sets to square them up.  My car has a tickle over 400hp and about to put an LSD in also, is 245 a little thin for a square setup? It kinda feels that way to me. Also, is there any tangible benefit to having 18's over 17's? Is the footprint demonstrably bigger? From those of you who went to light(er) wheels after heavy buggers, did you notice it much?
    • Start with the R32 GTR wiring diagram. The ECU is essentially the same, so the pinouts are good. The details around ECCS relays, etc might differ a little bit, but the reality is that you need to get ignition power to kick the ECU so it powers up the ECCS relay which brings the rest of the ECU up. This also gives power to the other circuits that are needed to make the engine run, like the ignition coils, etc. All of this is visible on the R32 diagram and should give you a strong guide, even if it's not quite the same as the R33. As to specifics - I'm pretty sure no-one can help you from afar, as there is no way to know what mistake or omission has been made in connecting stuff up. It always turns out to be "LOL, I shorted something and an entire wire vanished out of the loom", or "We never connected X or Y main connector", or "shit, you mean I need to have that fuse installed?".
    • hello wanted some insight on what my problem could be so i swapped a RB26DETT into my r33 gtst used a R33 GTR engine harness and im using a haltech platinum pro. The car cranks but no start the ecu isn’t getting any power now im trying to find out why i cant seem to find any schematics  or diagram for the engine harness for the r33 gtr anything helps thank you.
×
×
  • Create New...