Jump to content
SAU Community

Recommended Posts

seeing the section may be missed by alot of people in the QLD area, i just wanted to let you all know of this buy.

All skylines, stages GTS, to GTR....

White face dials from my bro in japan, this is the 2nd run for this buy, dont miss out.

http://www.skylinesaustralia.com/forums/in...howtopic=113600

a quick look at what i can get.

32gtr-b.jpg

And new to the line, full bezels for them.

R32-PR-HMb.jpg

follow the link and get in on this buy.

Thanks.

kezza

Link to comment
https://www.sau.com.au/forums/topic/114477-who-would-like-white-face-dials/
Share on other sites

can u get them for r34s?

Im looking at the moment, cause a few other guys are interested in them for the R34 GTT. at the moment i can only find R34 GTR ones.

Is this cluster the same set up for a man trans GTT R34?

post-14512-1145696253.jpg

there the other way round but i suppose it dont matter :(... how much were the 34 ones?

this may sound dumb, but how do get the nice blue glowing dashs? like the reverse glow ones?

there the other way round but i suppose it dont matter :(... how much were the 34 ones?

this may sound dumb, but how do get the nice blue glowing dashs? like the reverse glow ones?

yeah reverse EL ftw

you'll see mine tonight,



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...