Jump to content
SAU Community

Fs: Mad Turbo

danielson
 Share

Recommended Posts

danielson Proficient

danielson

Posted
Posted

located in thirlmere nsw, selling a high flowed nissan rb25det turbo. ratd at 500hp, it has the following specs:

high flowed turbo off a s1 nissan skyline. it has done 5674klms since being built, has no shaft play, has only run at 10psi, and is capable of 500hp. it has the following work done to it... high flowed machined front and rear housings, larger steel internals, new ball bearing packs, larger wastegate, new wastegate actuator (factory set to 10psi minimum), and ported exhaust housing. excellent condition. email me for pictures. cost of tthe turbo build was $1950.00, plus $450 for the turbo. now you can see how much of a bargain this is. It was rebuilt by xtr (gcg turbos).

make an offer or bid here http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...AMEWA%3AIT&rd=1

looking for around $800.00. i know it mite sound expensive, but it is a direct fit. no new manifold, pipes, etc. and its a great turbo

Link to comment
https://www.sau.com.au/forums/topic/114893-fs-mad-turbo/
Share on other sites
lukes146 Contributor

lukes146

Posted
Posted (edited)

will it be a direct fit to a 96' s2 r33? The only mods i currently have are front mount intercooler, 3.5" cat back exhaust (getting dump and cat done this week) would i need any other mods to support the turbo? or could i just get a mechanic to whack it on with low boost?

Also when does the turbo come on boost? do you have any dyno graphs?

Edited by lukes146
Link to comment
https://www.sau.com.au/forums/topic/114893-fs-mad-turbo/#findComment-2115393
Share on other sites
danielson Proficient

danielson

Posted
  • Author
Posted
will it be a direct fit to a 96' s2 r33? The only mods i currently have are front mount intercooler, 3.5" cat back exhaust (getting dump and cat done this week) would i need any other mods to support the turbo? or could i just get a mechanic to whack it on with low boost?

Also when does the turbo come on boost? do you have any dyno graphs?

it will be a direct fir. it would take about 3 hours for you to fit it yourself. and i dnt have any dyno graphs, but i can say it hits 10psi by 3200rpm. then goes like an ethiopian running to macas

Link to comment
https://www.sau.com.au/forums/topic/114893-fs-mad-turbo/#findComment-2115406
Share on other sites
danielson Proficient

danielson

Posted
  • Author
Posted

:(

hahahaha, love that ethiopian joke. alright you might have found yourself a buyer. Do you have the receipts for the build? and why are you selling the turbo?

unfortunatly my mechanic has the reciepts as he sent it to gcg, but the serial number is :AA428.

the receipt is available from gcg turbos. im selling it because the motor since shat itslef, so its the perfect reason to build a big f**k off 800hp motor. :) i have bought a gt42r and need more moolah if you no what i mean,

Link to comment
https://www.sau.com.au/forums/topic/114893-fs-mad-turbo/#findComment-2115449
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a good German place in Brisbane if youre up for the drive 😛
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...