Jump to content
SAU Community

Can Anybody Read This Please

FR34KU

By FR34KU,
in New South Wales

 Share

Recommended Posts

Sl!m Grand Master

Sl!m

Posted
Posted

I - Tec NISSAN skyline (R34) business door mirror turn signal

When this is installed, function as a turn signal of course is, but it raises also the high-class impression of the car!

Because the turn signal lamp is the automaker genuine products, function, both reliability it is relief.

From usual shopping going out to distance. From the street to the circuit anytime and it is the commodity of degree of attention rise anywhere. How probably will be for dress rise and safety improvement?

Installation method As for method of installation, 1 place boring the hole for wiring retreat through the door mirror itself, putting the cover, you connect to turn signal wiring of the vehicle. Processing the door mirror does not need in other things.

Finish FRP make white gel coat finish.

Accessory Mirror cover and turn signal lamp, wiring, both sides tape, installation instruction manual.

About paint Paint of the commodity is received for 8,000 Yen by demand.

In case of desire please request from order form.

The selfishness you limit the corresponding color of the paint being completed item, to the below-mentioned genuine color.

#QT1, ♯ KR4 and #QM1

Because paint is not the present car adjusting, as for the difference of somewhat color when we would like to receive acknowledgement, you know.

About payment date The commodity basically becomes incoming order production.

After payment date of the white gel coat item paying, usually it is 1 week.

In case of the paint item 10 schedules it catches there are times when to the delivery.

Pleaseinquiredetails.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...