Jump to content
SAU Community

Recommended Posts

i said is rego include insurance(3rd party)?

You need CTP (Compulsory Third Party) in order to get rego.

If your in NSW, rego is usually about 250, and ctp, depending on your age could be up 2 600.

Im 20 and pay 550 for CTP.

There are two kinds of third party insurance. Third party personal which is compulsory to get your car registered (often called CTP or green slip) and third party property which covers you for the damage you may cause to other people's property, eg their car.

The cost of rego is separate to either of these and is paid to the RTA whereas the CTP is paid to an insurance company.

I recently got registration for my car. I beleive that the third party insurance that comes with the registration is on for personal damage. Like "abo bob" said the cost of rego is separate to either of these and is paid to the RTA whereas the CTP is paid to an insurance company.

So you would pay extra for either Third party insurance of fully comprehensive to the insurance company to cover your car in an accident.

I think.....

1) rego= rta

2) ctp/green slip/third party personal= insurance company

3) third party property= insurance company

to get rego you must pay for no.2 first at the insurance company then go to the rta and give them proof of your green slip then you pay for rego.

then you stick your rego sticker on your car!!!!

green slip only covers people that are hurt in accidents not property!

you need another insurane no.3 to cover the damage you do to their property

From a QLD'er

You have to be more specific mate. Same like the other in NSW

---> Compulsory Third Party (Which is the one you need a Safety Cert For to register your car on the road and get CTP)

---> Extended Third Party (AKA Third Party property damage - This the middle which covers you for damage/fire/theft to a certain amount)

---> Comprehensive (we all know this one)

From what i gather you are asking about the Rego where you pay it all at the Dept of Trans (CTP). AND yes rego does come with your payment, if your car is already registered.

So you have to be more specific and not have a go at someone who is trying to help mate.

From a QLD'er

You have to be more specific mate. Same like the other in NSW

---> Compulsory Third Party (Which is the one you need a Safety Cert For to register your car on the road and get CTP)

---> Extended Third Party (AKA Third Party property damage - This the middle which covers you for damage/fire/theft to a certain amount)

---> Comprehensive (we all know this one)

From what i gather you are asking about the Rego where you pay it all at the Dept of Trans (CTP). AND yes rego does come with your payment, if your car is already registered.

So you have to be more specific and not have a go at someone who is trying to help mate.

But you don't get it! The in the third party is the in the included?

I think that's what he is trying to say.

But seriously....If the car is already registered then the registration renewal form you get does include compulsory third party from the previous CTP insurer...unless you want to change.

CTP Extended is not included.

Or pretty much what Arbess said.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...