Jump to content
SAU Community

Recommended Posts

I had tubo back exhaust, SAFC2, and 10psi of boost before I installed my hybrid cooler. After the install I had to regap my plugs and get the safc retuned as the car was braking down due to the higher and more efficient air flow. Please note thats without increasing the boost, once tuned it made a huge difference heaps more power and I could not notice the difference in thottle responce. Very worth while mod from my experience but do your exhaust, gap plugs to 0.8, and get a SAFC2 or Power FC first. I made 195rwkw on 10psi not holding boost. I suspect I would be making just over 200rwkw now, its holding 11.5psi to red line, I have installed also a sheilded Pod filter and a cold air feed.

I think what most are trying to get at is the intercooler it self won't actively give you a power increase but by fitting it you will enable the motor to produce the power it's capable of by removing the restrictive, heat soaked and poorly positioned factory unit! An aftermarket unit will

A, generally flow better due to the piping and larger core size/design . . . . and

B, cool better due to sheer size and positioning for max air flow through it

So the combination of a cooler charge and less restriction (less pressure drop) = a cooler slightlty higher pressure charge at the manifold which we all know means a better burn and more power!

And alot more consistant charge temps to boot!

So getting a SAFC or PowerFC is the first thing to get then an FMIC???

Cuz i have the same mods exactly..(HKS Pod, Turbo Back, Stock BOV) n running 10-11 Boost... according to the Stock Boost Gauge.. which is 3/4 way up to Full..

Can u Increase the Boost More once u get a FMIC??

-SeSaR

Edited by Black_CSR

Chirping gears doesn't prove a car is fast. It simply proves you have a very good clutch, hard tyres and slam the gear damn hard.

Chirping gears is stupid, it puts un-necessary strain on gearbox's and will stuff your diff early. :(

Every R33 I've seen run more than std boost picks up power when you drop an fmic on them. Its not much, hardly noticable.

R32's... Well mine didn't.

but it's hektik to chirp on gear change.

I can chirp all 5 wheels (including the spare in the boot) 6th gear on my rb20 powered gts4, down hill, on drag slicks..

i have exhaust, filter, 11 psi boost and a boost gauge that has 7 colours.

respetk

oh I forgot to mention I have a fmic...

Edited by GTST
So getting a SAFC or PowerFC is the first thing to get then an FMIC???

-SeSaR

NO NO NO

Install the fmic FIRST then do a Safc or Pfc.... otherwise you're up for 2 tunes, like me! doh. I had a safc yadayadayada etc, put in an Apexi fmic, too much airflow stuffed up the safc tune, couldnt boot it anymore, needed a retune (although I had a Sitc waiting to be tuned too, so I needed to go on the dyno again anyway)

NO NO NO

Install the fmic FIRST then do a Safc or Pfc.... otherwise you're up for 2 tunes, like me! doh. I had a safc yadayadayada etc, put in an Apexi fmic, too much airflow stuffed up the safc tune, couldnt boot it anymore, needed a retune (although I had a Sitc waiting to be tuned too, so I needed to go on the dyno again anyway)

I should have been more specific like tangles said get your intercooler installed then install you safc or power fc or you will be up for 2 tunes like us. Many have found with the increase of airflow the stock ECU cant handle it and will result on overly rich AFR which causes flat spots hench the recomendation of SAFC or Power FC. Personly I would not run anymore than 11psi

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...