Jump to content
SAU Community

Any Of You Know If A Rb20 O2 Sensor Will Work On A Rb25det Series2 Engine?

NateR31

By NateR31,
in Engines & Forced Induction

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

It doesn't give the correct voltage readings the ECU requires to do its closed loop operation. Therefore it's not economical. But it's not like the car won't run.. you can unplug totally it and drive around - it just will suck a lot of juice.

I tried one of these "EL - fits R33/R32" sensors into my old rb20det.. and plugged in the consult port and voltage was all over the shop. Since then a few are adament it's fine on an rb25.. but I haven't yet stuffed around checking how the ECU reads the voltage on the rb25 ecu yet.

BH_SLO32 Proficient

BH_SLO32

Posted
Posted

I've run the RB20 sensor on my RB25 for a period with no noticeable side effects. The range of the sensor read by the RB20 and 25 ECUs is the same so I couldn't imagine there would be any real difference although I am not sure.

NateR31 Grand Master

NateR31

Posted
  • Author
Posted

reason i ask is that my o2 sensor died so i was eating alot of fuel, i tried the EL sensor thing, checked on the pfc controller and its working, but i dont know what volts and ect.. its ment to be on.

can someone see what volt at what rpm it should be?

mad082 Grand Master

mad082

Posted
Posted

$105 from autobarn for a direct fit o2 sensor. it is the proper one. it also fits sr20 pulsars and nx-r's. part number OX-203 otherwise for an extra $5 you can get a NGK one, but i don't have a part number for it, but it is listed in their pricelist (has R33 in there. thats how i know it is the same one as in a pulsar. same part number).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Ball bearing turbos

      By sunsetR33 · Posted

      Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • GTSBoy
      R33 GTST Axles

      By GTSBoy · Posted

      There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • thozza
      Intro/R33 owner

      By thozza · Posted

      Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Lithium
      Forced Performance Hta Turbos

      By Lithium · Posted

      Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...