Jump to content
SAU Community

Recommended Posts

can someone help me out here i have a r32 with minor mods, but the weird thing is that the turbo doesnt start to spool until 3 to 3.5 grand and hits full boost at around 5grand, wat does this mean is it not standard turbo or is it fu%^ed.

any help will be appreciated.

Joel.

This will sound weird but my r33 was doing the same thing and it turned out to be my fuel pump so i put a walbro in tank one in and it is fine now. Im not sure why the boost was coming on late all i no is that the new pump fixed the problem.

Link to comment
https://www.sau.com.au/forums/topic/116674-r32-stock-turbo/#findComment-2145853
Share on other sites

"""has the car been feeling sluggish? is it noisier at all when under boost?

you may have a slight leak in an intercooler/inlet pipe? checked all the clamps?""" (Azzurra)

no not slugish at all. it does seem to sound a little noisy i'll check the clamps...

well it has an aftermarket fuel pump an gtr injectors, an a malpassi fuel pressure regulator, but iv also noticed it only does it sometimes. Also Is there anyway to tell it the turbo has been high flowed-(rebuilt) without removing the turbo its self.

cause iv tested it on 12psi boost with out a FMIC an it runs perfect, iv been told not to run more then 10psi without a FMIC. i dont kno wats been done to it personally. also has a high flow cat an 3" system.

Edited by HR32_GTS-T
Link to comment
https://www.sau.com.au/forums/topic/116674-r32-stock-turbo/#findComment-2145964
Share on other sites

just sitting idling for a while, give it a bit, an then give it a bit later an it hits full boost at 3grand instead of around 5grand, weird i kno, but everything runs sweet an she go's hard, wat about the boost controller, i have no idea wat brand it is either, but it looks shitty.

Edited by HR32_GTS-T
Link to comment
https://www.sau.com.au/forums/topic/116674-r32-stock-turbo/#findComment-2145998
Share on other sites

mate my car has the same problem i hit boost at 3000rpm but dont hit full boost till i hit 4500rpm i have a rb25det neo with an r33 turbo on it i wood like to no y it is doing this as it only just started playing up

i will go and c my mechanic tomoro after work and ask him i will let u no how i go.

ps if any one on here can help me plz let me no thanks

Link to comment
https://www.sau.com.au/forums/topic/116674-r32-stock-turbo/#findComment-2146474
Share on other sites

Check to make sure the wastegate actuator is not staying open. If it sticks or is getting stuck on something then it will be bypassing the exhaust gasses around the turbine. The easiest way to test this device is with a radiator pressure tester. Use it to pump pressure into the housing and confirm that the pressure it opens at is equal to the factory specs. If check is ok remove the mounting point where the actuator connects to the wastegate arm. There should be a small circlip. Use a pick or small screwdriver to remove it but be careful not to lose it. Check to make sure the arm moves freely and can open and close fully without interuption.

Check to see how easily the arm moves back and forth in the diaphragm. It should be difficult to move.

Link to comment
https://www.sau.com.au/forums/topic/116674-r32-stock-turbo/#findComment-2146807
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...