Jump to content
SAU Community

Recommended Posts

  • Replies 513
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

It must be easy to see for marshalls

Thats all

But at Oran, almost all the numbers were easy to see, problem was, the numbers made the cars look like shit in some cases after the day when it came time to looking at photos :kiss: It does make a difference

I've just made my number (but I'll still like the Steve-0 version).

Basically printed out the two numbers (each number about credit card size) and laminated them both.

Maybe a little small~

If the timing beacon is at the fishhook then you will need something like this

http://transelite.net/powerplay%20web/pages/PICT0467.htm

This sizing is to within CAMS specification for racing

If it is on the start line then something like this will be sufficient

http://transelite.net/powerplay%20web/pages/PICT0060.htm

I think you should only be allowed to run if you have numbers permanently stuck on your car.

So that’s all you guys out and there’s room for me.

:wub: cheers :(

rofl

Ill sell you my ticket for $5000. kthxbye. New turbo for me!! :D

Ok, so i had to take a call, and it took more than a minute

SAUnumbercards002.jpg

SAUnumbercards001.jpg

And so on for the others (couldnt be stuffed covering the floor with EVERY single one)........

So thats one less thing you lot have to worry about :D

what does the small writing say?

btw, that's a really nice thing of you to do Steve bigthumb.gif

It says the persons name incase they forget their number :wub:

Cheers mate!!!

Oh you must be busy @ work steve.. lol

Yeah, todays had its moments :D




  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...