Jump to content
SAU Community

Lenso 19inch Wheels & Tyres (concept Five) Suit Skyline Gtr's Or Consider Swap For R32 Gtr Factory Wheels.

petmod
 Share

Recommended Posts

petmod Apprentice

petmod

Posted
Posted (edited)

Lenso Concept five 19inch wheels v, good tyres suit skyline GTR's, selling or willing to swap for R32 GTR factory wheels with money on top. Out right I want $2200 or R32 GTR wheels and $1000.

Edited by petmod
IOWNU Grand Master

IOWNU

Posted
Posted (edited)

Got any pics?

Also what city are you in?

I have a spare set of 32 GTR rims.

Edited by IOWNU
  • 1 month later...
PranK Grand Master

PranK

Posted
Posted

oh man... what a joke of a thread..

Listen dude, if you want to sell your wheels, you might want to consider adding the folliwng;

- Condition

- Offset

- Width

- Tyre type and size

- Tyre tread left

- LOCATION!!!!!!

- And, if possible, pics...

Trust me, it'll help a lot!

Christian

RRR033 Newbie

RRR033

Posted
Posted
Lenso Concept five 19inch wheels v, good tyres suit skyline GTR's, selling or willing to swap for R32 GTR factory wheels with money on top. Out right I want $2200 or R32 GTR wheels and $1000.

do you have images you could email me?

which state are you in, and do they come with tyres and what size, tread, brand etc

PranK Grand Master

PranK

Posted
Posted

closed... what a waste of space...

You will *need* to post more info next time... You were asked several times for the same info which you never posted.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...