Jump to content
SAU Community

I Need Grip!

Rosie_1008

By Rosie_1008,
in Tasmania

 Share

Recommended Posts

phat_r33 Rising Star

phat_r33

Posted
Posted
sorry to hijack ur thread Rosie....

but has anyone had experience with Falken Ziex Tyres? I believe the 326 not the 512 "all season" tyre.

Getting 18 x 9's on my Hr31 coupe and want it to grip.

Going coilovers front and rear and it currently has 200+ atw, shooting for 220-240rwkw soon.

cheers.

Just re-emphasising my earlier point but for street tyres you really can't go past federal. I have tried ALOT of tyres out, and with a T76 on my car I have only just started to wheelspin under 2bar boost and have had the tyres on for almost a year. Mind you I don't go doing fully sick burnouts but not afraid to boost. Only tyres I have tried that have held up to it. Falken are cheap and nasty IMO, very dissapointed with them, pirelli were good, nankang very bad, can't remember any others.

smudgee69 Explorer

smudgee69

Posted
Posted

Gidday Rosie, ive put a set of dunlop sp 9000s on my GTR and they dont seem to do anything wrong. Mine are 245/35/18 and not real cheap but you are probably runnning 17s by the look of it so go for a 17 with no less than 40 profile, that should ride a bit better for you. If Steve Bell is doing your engine you must live in Launie. Just remember your first expense is your cheapest expense, do it once do it right. Sounds like you have a boost controller on it so once the engine is a runner get it to Brad at Chris Colgraves at Invermay and he will tune and set the boost for you, say no more that 17pounds on premium will be fine. As far as the clutch goes fit up a standard system to make it user friendly. If you get stuck for engine components give me a yell i might be able to source it for you. Dont be frightened to ask others for advice on prices etc, no need to spend more than you have to. If you want to sell that clutch i might be interested, cheers paul

XRATED Veteran

XRATED

Posted
Posted (edited)

Even still Rosie if your not comfortable driving with it, and your not going to get seriously into drag racing, I'd sell it and get somthing more user friendly. After a few weeks of driving around with somthing like that, you'll start to not enjoy driving your car, if that happens, then why have the car in the firstplace.

Even if you do wan't to race, Matty Rickards was running hard for 3 or 4 drag meets, all he was using was a Jimm Berry single plate and didn't have any problems.

J

Edited by XRATED
smudgee69 Explorer

smudgee69

Posted
Posted

Rosie, i agree with the x-man 100%, although your mechanic has said your twin plate is an excellent clutch, no-one is disputing that. The facts are its a dog of a thing to drive and you obviously cant come to terms with it so i agree with the x dude, a jim berry set up is an excellent cluch, single plate, light pedal yet delivering over 2 tonnes of plate pressure good for more Kw than you will ever have, its a cloned subaru clutch and would be my first choice for a street machine. I have a new nismo twin plate and it like yours is a pig to get going at the lights but i intend to do track work, if i didnt the jim berry would be strait in, food for thought, cheers Smud

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...