Jump to content
SAU Community

Rattling Clutch Pedal Or Clutch Assembly?

WAN73D

By WAN73D,
in General Maintenance

 Share

Recommended Posts

WAN73D Collaborator

WAN73D

Posted
Posted

hey guys....got a minor prob (i think) with my 1990 r32 gtst

i noticed recently (i think it's gotten a tiny bit more noticable over time), that since i changed my clutch there is a fairly high pitched rattling sound coming from the front end of the car at idle. But as soon as a press the clutch peddle down it goes away.

I have also noticed that it goes away when i step on the clutch just slightlly (without actually making the clutch release yet, if u know what i mean) so to me it seems to be something to do with the pedal assembly.

clutch works fine...just that this sound is pissin me off.

anyone got ideas?

thanx again

wrxhoon Grand Master

wrxhoon

Posted
Posted
it's only a single plate clutch

so what's this thrust bearing??? and why would it be making a noise when i'm stopped in neutral. DO you think this is a problem because the car drives fine otherwise?

If its a rattling sound its not the thrust bearing, they make a different sound, if you have an old bearing without grease in it spin it fast and you will know what a bearing sounds like. If it just rattles its the clutch itself. Is it a button clutch ? Who installed it?

If its a bearing sound it could be the main shaft bearing in the gearbox and it goes away when you press the clutch in because its not turning. You should hear that while you are driving as it then turns again .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • RB25inside
      R34 Handbrake light saying ON and intermittently flashing

      By RB25inside · Posted

      Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The Bogan
      Wheel Sizes & Offsets For Skylines

      By The Bogan · Posted

      The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...