Jump to content
SAU Community

Recommended Posts

I want to get the fuel pump out my tank and have a quick look at it and see whether the internal filter needs cleaning.

How do I go about this? Do I have to drop the whole fuel tank out and remove it from the top?? I have seen in some other cars there is an access panel from say the boot or whatever that makes removing it pretty easy without pulling the tank out - anything like that on the R33 ?

Link to comment
https://www.sau.com.au/forums/topic/11783-removing-fuel-pump/
Share on other sites

no tank dropping required whole assembly comes out through the boot

acess pannel in the boot

then unscrew the plastic cap and remove assembly from in tank

i did this once but i dont recomend doing this it is a dangerous procedure and the whole boot fills up with fuel vapours

one spark and boom you now have no face

aswell as the bad effects fuel vapours can have on your lungs

after 5 min of fiddling inside the tank i was completely ****ed up

i had no idea how high you can get on fuel vapours

not a good high mind you killer headache and loss of balance

and also

spinnin`...

spinnin`....

spinnin`

make it stop

hehehe..mygtst - I don't intend on standing there inhaling the stuff to get high :) I'd take it out in the open and like v-spec said make sure most of the fuel is out of it first.

I know petrol is smelly stuff. Shoulda seen when I changed my fuel filter.. petrol dripping everywhere ..and i did that in the garage :D

So where is the panel? I had a look in the tyre well and couldn't see anything. Is that the plate near the fuses and battery behind the rear seat (yes, remove battery first, safety first, blah).

predator.. haehaeh wat a co-incident. i was thinking about the

same thing and gave it a try...

what MYGTST said is right. well right from what i could see.

the cap is soo hard to turn cause of the rubber seal. once i pulled

it open the pump sat all the way down at the bottom so i suggest

emptying it as much as possible.

I'm not sure how to take the pump out tho.. it was very cramped

for me.. Let me know how u go.

...more to the point - how does it go back? apparently it sits at the bottom of the tank face down and sucks. If I just pull it out I might not be able to put it in the proper position - causing major probs for fuel sucking.

the pump sits on a metal bracket which is clipped in place all you have to do is unclip the metal bracket and it comes out with hoses and attacments

the pump is clamped to the bottom of the bracket so you simply clamp it back in the same place once your done

to remove the assembly you need to feel inide and slide the bracket up and to the side and it unlocks

the access panel is in the raised section of the boot on the right hand side and yes the plastic cap is a pain to get off its so tight

i recomend removing the battery from the car during tank opening

less chance of sparks

byt he time you figure out the how the bracket comes out you will be well and truly high even if your tank is almost empty

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...