Jump to content
SAU Community

Recommended Posts

Specs:

- Garrett 3037 ball bearing turbo

- Greddy plenum

- Greddy triple core drag S15 radiator kit.

- Craig Davies 16inch thermo fan

- HKS Type R Drag Intercooler

- 38mm Turbosmart wastegate

- Customised Race Pace stainless piping throughout turbo/intercooler setup

- K&N Air filter

- HKS Hi Power 3inch Cat back exhaust

- NISMO 750CC INJECTORS

- Bosch 044 external fuel pump

- XTR custom surge tank

- Sard fuel reg

- CUSCO 1.5 way LSD -

- Project mU slotted & drilled discs

- BREMBO R33 V-SPEC calipers.

- CUSCO BRAKE CYLINDER BRACE

- CUSCO FRONT STRUT BRACE

- CUSCO REAR STRUT BRACE

- JIC MAGIC FULLY ADJ COIL OVERS

- NISMO REAR ARM ASSEMBLY

- upper & lower links

- C's short shift kit

- Micro tech LTX8

- Bosch individual coil packs

- 18INCH VOLK RACING CHALLENGES in rare diamond black

- D-SPEED WIDE BODY FLARED/GILLED FRONT GUARDS

- CWEST Spec 2 FULL BODY KIT

- NISMO CLEAR INDICATORS

- NISMO PETROL CAP

- NISMO RADIATOR CAP

Located in North Sydney

11 Months Rego in New South Wales

No accidents

Slight damage around front drivers side 1/4 where wheel hits the lip

No offers

No trades

No time wasters

Pics

1159617.jpg

1159620.jpg

Will take more if asked.

Link to comment
https://www.sau.com.au/forums/topic/117834-fs-modified-2001-s15-sydney-34000/
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...