Jump to content
SAU Community

How To Know If Cracked Head Or Gasket?

SXC_R33

By SXC_R33,
in Engines & Forced Induction

 Share

Recommended Posts

SXC_R33 Mentor

SXC_R33

Posted
Posted

hey guys a mates r33 gtst out of the blew has started to idel very rough and it begain to over heat so all hoses have been changed and flushed the system and added coolant.... also when car is turn off water in the overflow bottle is bubbling???? anyone know whats going on

all help is much appreciated???

ODessA Collaborator

ODessA

Posted
Posted

take the radiator cap off and let the engine idle, if the water bubbles and froths up and has oil in it then u prolly blew a head gasket, take it too a mechanic they got a thingy they put on there and if it loses compression etc etc.

brother_david Rising Star

brother_david

Posted
Posted

I guess this wont help, but anyway...

Had the same prob on my BMW, the earlier owner had changed headgasket, rebuild the head, and changed cooler along with some other things, when i bought it.

It acted the way you describe, but there werent any oil in the water etc, and if it idled for a somewhat long while it started to stutter, and the water in the overflow bottle started bubble.

Someone mentioned i should check if there were air in the watersystem, and there were some, got it out and now its a whole lot better.

Probably wont help you but who knows, it might :thumbsup:

Craved Grand Master

Craved

Posted
Posted

bleed the radiator again, using the tap near the plenum that has the label "do not open when hot"

other test is for exhaust gas in the cooling system.. they put it over the cap and it changes colour if gases are in it...

for $330 for a cometic metal gasket and time if your mechanically minded then you can fix it up easy and cheap if it does show gas.

BezerkR32 Veteran

BezerkR32

Posted
Posted (edited)

water is going out the exhaust brother, Chemical testing the system is the way to go, blown head gaskets dont always blow to an oil gallery, most common is cylinder to cooling system. other test is to pressure test cooling system with spark plugs out, then crank engine, if water is blown out of spark plug tube, thats bad.

something has caused the car to overheat, repair leak, check thermostat, flush radiator. Blown headgasket is the result of something else failing.

' date='23 May 2006, 06:34 PM' post='2194735']

could it be the water pump?

where does the leak go to?

Edited by Bezerkly

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...