Jump to content
SAU Community

Recommended Posts

remote Breather tanks for radiators ..

already running a PWR 40mm radiator but she still bubbles a little after getting hot ..

d1specheadtank.jpg

are kits like this useful on systems that already run header tanks with the presuure caps?

only ever seen them on sealed cross flow units..

any ideas??

Link to comment
https://www.sau.com.au/forums/topic/118629-remote-breather-tanks-on-radiators/
Share on other sites

Hey Chris,

I got one of these installed; main reason for it is to remove air locks which it is doing just fine.

My tank is setup where the stock charcoal cannister is and does the job pretty well!

NB: There is a T-Piece that you require in order to make the product you've shown work, it's not included!!!

S

oh, i thought u already had one. how come the plenum now stops you from bleeding the cooling system?(never done any cooling system work on 33's maself) i cant really see how they would be of much benefit on a system that already has a header tank with pressure cap though.. basically, they do the same job. does the factory header tank have any form of 'breather'? if not then this might do sumthin for you

Hey Chris,

I got one of these installed; main reason for it is to remove air locks which it is doing just fine.

My tank is setup where the stock charcoal cannister is and does the job pretty well!

NB: There is a T-Piece that you require in order to make the product you've shown work, it's not included!!!

S

hmm would like to see how its hooked up, cant really picture it... does it pull a water feed from somewhere like where the std water bleed is?

oh, i thought u already had one. how come the plenum now stops you from bleeding the cooling system?(never done any cooling system work on 33's maself) i cant really see how they would be of much benefit on a system that already has a header tank with pressure cap though.. basically, they do the same job. does the factory header tank have any form of 'breather'? if not then this might do sumthin for you

the front facing plenum relocates the TB, and since it dont really snow here i didn't run the water feed through the throttle body .. hence its removal..

Edited by Craved

The tank is situated in between the overflow tank and the radiator... in total I think there are 4 lines coming off the thing, 2 going back into the radiator (well one from and one back to)

The other hoses then go to the over flow and one has a one way air bleeding cap (trying to be descriptive)... it lets air out but not coolant (?!?)

Not 100% sure, the boys put it in and said it works :wave: I'm happy and was content with a 80% understanding :wub:

hahah once i see it i will get it fine..

can see where the return from the tank to the radiator would enter the cooling system as the pressure cap on the radiator wouldn't allow water back in very much.

got a picture Stan?

bleeding air from the system is extremely important - more so than people generally think. air in the cooling system is a killer and will turn the block into a kettle - particularly when we have lengthy 6 cyl engines and there is a significant temp differential between the front of the block and the rear as the water from the radiator only enters at the front.

some aftermarket chevy heads now have cooolant take offs half way down the side of the head for that reason - more even core temp means more consistent combustion and more efficiency.

the breather tank is probably a good idea in a high hp engine, one that operates at higher temps for long periods or one that has no bleeder :O make sure it's at the highest point of the cooling system otherwise it just acts as an extension of the water jacket and, instead of turning steam into condensation will recirc the steam.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...