Jump to content
SAU Community

Recommended Posts

Hey all,

I have just purchased a pair of new L.E.D Tail Lights which look outstanding...

However, i have been unable to remove my old tail lights, i have removed the 5 nuts from behind the panel and just curious if others have been able to remove and or replace their old lamps...

How do i remove the tail lamps so i can put my new and improved tail lamps in?

How do i remove the facia plate to put on my new LED tail lights?

If any others have removed their tail lamps please help me out... Thanks

Link to comment
https://www.sau.com.au/forums/topic/118933-tail-light-removal/
Share on other sites

I was also wondering the same thing, but mine is more for maintainance purposes. I think you're right with the 5 nuts. I did the same. I think the only thing holding the light assembly in place now is the gooey black stuff. This is a silicone based sealer (I just bought some to seal leak at top of light). I'm not too sure as to how you go about it, but I think that's all that is now holding it in.

good luck with it.

When you do manage it, let us know what you did...

cheers.

im pretty sure the r33 is the same as r32.

yes u are on the right track, the black silicone is the only thing left holding the light in place after the screws are removed. i used a hair dryer to heat up around the glue and when it was hot enough, it came out.

all you have to do is get the dryer and heat up the silicone up evenly (heat up all the silicone at the same time) using a circular motion. at the same time apply some force with the other hand and slowly as the silicone heats up, the light will slowly pop out. just try to pop it out quick when the silicone starts to go, as you dont want to make a mess of it by stretching it everywhere.

good luck

Hey man a little bit off topic but where did you get them, how much? and do you have pics?

cheers

I got them off of e-bay... There are about 3 different sets on there... I bourght the more expensive ones at $480 but they look the part... Really do look spectacular when they have been lit up at night and even during the day... Well worth the money spent... I have no pics on my comp but just look on e-bay for the images...

im pretty sure the r33 is the same as r32.

yes u are on the right track, the black silicone is the only thing left holding the light in place after the screws are removed. i used a hair dryer to heat up around the glue and when it was hot enough, it came out.

all you have to do is get the dryer and heat up the silicone up evenly (heat up all the silicone at the same time) using a circular motion. at the same time apply some force with the other hand and slowly as the silicone heats up, the light will slowly pop out. just try to pop it out quick when the silicone starts to go, as you dont want to make a mess of it by stretching it everywhere.

good luck

Hey man, thanks for the tips on getting the lights set out... But what about the facia plate? Does that come away form the unit so i can attach it to my new set of lamps? If you know please help me out...

  • 1 month later...

Sorry for the ultra late reply but have been busy with other issues with my car...

but i successfuly changed the rear tail lights to very nice LED tail lights about 2 weeks ago...

Was just as every1 said, remove the 5 nuts and use a heat gun to heat up all the sealer and came off easily...

Anyway here are some before and after photos... (before photos are from when i first purchased the car so they look a little older)

post-25223-1151212956.jpg post-25223-1151212978.jpg post-25223-1151213027.jpg post-25223-1151213146.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...