Jump to content
SAU Community

Recommended Posts

i have an auto r32 gtst and this might sound like a stupid question but i havn't owned a turbo car before so be kind.

does the auto gtst still have a stock bov?

if yes i think mine does not have one as when i'm on boost and i take my foot off there is no noise like one would expect.

also, if yes then where is it located? on my intake piping before the throttle body and before the bend there is a small pipe which runs off the main pipe which leads to nothing and is blocked off...anyone know if this is where it should be...or does someone have a pic of a stock bov which i can compare to. maybe its there but stuck or something.

as i said i havn't owned a turbocharged car before so i am learning as i go...

thanks,

Waz

Link to comment
https://www.sau.com.au/forums/topic/11910-bov/
Share on other sites

MM2death has given you the pic.

If your one isn't making any noise, then it is probably because you have the standard air box.

When you have a pod filter, it is very free flowing and you can hear all sorts of induction noises.

also, when the bov vents, you will hear a sshhhhh sort of sound.. different to the aftermarket psshhtt sound.

the standard bov makes more like a hissing sound.

IF your bov is removed and all holes are blocked off, and you put a pod filter on, when you back off from the accelerator, you will hear a fluttering sound.. like ch ch ch ch ch ch

Hope this helps.

And there are a fair few turbo cars (engines) that don't have bovs as standard..

here are a few.

Cordia turbo.

CA18DET engined cars.

VL Turbo

That's a few off the top of my head.

Link to comment
https://www.sau.com.au/forums/topic/11910-bov/#findComment-211395
Share on other sites

Originally posted by WazR32GTSt

on my intake piping before the throttle body and before the bend there is a small pipe which runs off the main pipe which leads to nothing and is blocked off

Mate... if someone knows what that is i'll fall off my chair.

ALL Auto's i've seen... R31/R32 (imports we are talking here) and i'm assuming it's the same for a 33 but ain't seen and auto one yet.

They all have that little pipe thing your talking about and it goes nowhere and does nothing. (that i know of)

It's also the easiest way to tell if you car has had a manual conversion done to it at any stage :(

Link to comment
https://www.sau.com.au/forums/topic/11910-bov/#findComment-216550
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...