Jump to content
SAU Community

Recommended Posts

lol wats up now andy?

Stoopid over heating, And I need to drive to Sydney!

And I need to buy a new cat before the tune (I have known that for a long time) And I cant decide what to do Re the radiator

well if u've got overheating problems, ud wanna get that fixed before u hit the track. if u've got the coin, go for one of just japs $399 radiators. that way u wont hav to worry about it ever again. or it could be to do with ur thermostat? prolly check ur thermostat first, see if its opening properly (pull it out, put it in a saucepan at the temp its spose to open, and see if it does actually open)

those catco cats off here are good :(

P.S i checked the front wheels, and none have lock nuts, bunch of tools :sick:

Eddie - have not seen you out cruising around for ages, hows the car going?

laters dan

(60NER)

Being Rebuilt atm Mate, have no seen u since i bumped into u in the city with those chicks u had with u hahahaha

Skyline will be back soon Full RB30DET, Gt35r... pretty massive setup...

well if u've got overheating problems, ud wanna get that fixed before u hit the track. if u've got the coin, go for one of just japs $399 radiators. that way u wont hav to worry about it ever again. or it could be to do with ur thermostat?

those catco cats off here are good :(

P.S i checked the front wheels, and none have lock nuts, bunch of tools :sick:

I was thinking one of them and I got a super special Pedros cousins sweet hookups price on one from JJ...but then I was told they are infact crapper than the stock ones :( Hence why I am stuck with what to do!

I got a super special Pedros cousins sweet hookups price on a catco from JJ :D

The one at the very bottom of this list http://www.justjap.com/parts_nexhaust.htm

what can i say, given the situation after what u tryed to do with my missus i guess u have to laugh it up.

LOL! here we go! more cod shit.

dude, get over it. nothin happened.

but seriously, you should go back to cruisingbrisbane and pm a few more chicks to offer your helping service on there and lend a hand in exchange for those roots you ask for after working on their cars.

LOL! mods are having a field day with you on there.

well if u've got overheating problems, ud wanna get that fixed before u hit the track. if u've got the coin, go for one of just japs $399 radiators. that way u wont hav to worry about it ever again. or it could be to do with ur thermostat? prolly check ur thermostat first, see if its opening properly (pull it out, put it in a saucepan at the temp its spose to open, and see if it does actually open)

those catco cats off here are good :(

P.S i checked the front wheels, and none have lock nuts, bunch of tools :sick:

PS I knew it didnt have lock nuts >< Damn loosers

Hows it going anyway? All good?

lol yeah, cant believe they reckon it did *shrugs*

yep its all good, gonna ring em up in a min to see if they're done. they've got a few nice race cars in there, a lotus elise, some GT car

lol yeah, cant believe they reckon it did *shrugs*

yep its all good, gonna ring em up in a min to see if they're done. they've got a few nice race cars in there, a lotus elise, some GT car

Wicked! Those Tyres should make it a bit better to drive!

Now all it needs is a clutch lol

Ooo I like elises...exige is better but

LOL! here we go! more cod shit.

dude, get over it. nothin happened.

but seriously, you should go back to cruisingbrisbane and pm a few more chicks to offer your helping service on there and lend a hand in exchange for those roots you ask for after working on their cars.

LOL! mods are having a field day with you on there.

yeh i could hey, f**k yeh pick up some 14 yo old broad minded persons root em then toss em your way?? although rape isnt my thing John... but we ( me and my gf, and the 2 other chicks u tryed to do it to ) will all agree that its ur style.. if u have anything further to say mate take it to PM

Hey Bunta!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...