Jump to content
SAU Community

Recommended Posts

Thats still pushing the envelope a little, from what i heard 300rw is about the limit

If you are lucky...I would sat the safe limit is really more like 270rwkw....300rwkw may last....for a month or two

LOL!

there is a power outtage out at shane's office.

he's offline till the other I.T. guy gets out there

roflol!

funny stuff

LOL

shane wont be back till after 3.30.

eta time given for power to be restored.

lol!

too bad we all got the shits and went home :P

now who'se the one laughing caus ur at work and im at home :P

It was an absurd example used to make a point?

Oh...

Well what I think John is referring to is the incident between me and Eddie where he was being racist and I got pissed off and then we proceeded to naming a place to meet to "sort things out"

The thing that was most disturbing was that there was no apology for the comments but instead just heaps of threats on how he would put me in a wheel chair. And he's still on here trying to be nice...

every post of his I have been trying to ignore but it still pisses me off that he can still come in here with out apologising for that comment and now want to join the club....

BTW I did turn up that night at Milton and he was no where to been seen.........

I might be kicked out of the club for my comments and getting involved with causing trouble but if it’s okay to post racist comments on this thread with out any consequences I’m very worried and might have to reconsider things....

P.S. Banning for 3 days is hardly consiquences

Anyone know a good place to get a personal loan? Or will finance a import?

personal loan, id sugest go with the bank who u've had an acoflamin mongrel with the longest, as ur more likely to get a loan with them. also u can look at wizard, u go in, tell them what u want and they check around different banks to see what they can get u

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...