Jump to content
SAU Community

Recommended Posts

He's running, has been for 4 weeks now, no nasty noises (except the VCT upon start up) and he doesn't sound too much like a tractor, exhaust choice is important with sr's, get a shit one and you might as well be hookin around on dad's ride-on :(

Gotta get him tuned though, 4000 rpm limit sucks dick, i'm changing outta 1st when i'm barely off the line :P So when i've got some spare cash (before Drag day) he's going back to EFI :(

yeh agreed with the exhaust - i discovered (unfortunately) that if the front and dump pipe is fitted correctly it sounds far less like a tractor lol

should be exciting once the tune is finished :)

Brisbane real estate sucks ass, where I want to be anyway...I need to be in or near the city and it's just too inconvenient to buy something i'll only live in for a year. I'll rent some heinously overpriced monstrosity until I decide if i'm going on secondment overseas and/or which city office I want to permanently locate myself at.

Brisbane real estate sucks ass, where I want to be anyway...I need to be in or near the city and it's just too inconvenient to buy something i'll only live in for a year. I'll rent some heinously overpriced monstrosity until I decide if i'm going on secondment overseas and/or which city office I want to permanently locate myself at.

I have one in riparian plaza, bank value $3.8million. For you.. $2.8million.

Brisbane Real Estate sucks if you need to sell in the current market.. It's a friggen cash cow if you have the captial to buy + pray on the kooks who over borrowed.

CBD is a bit of a c*nt though, I was based in there, banks were starting to ask for 40% deposit. By-by investor market

Haha, I know. The reality is I just don't want that sort of capital tied up, I can do more exciting things with it. If I were to buy property it'd more likely be cheaper investment properties.

Find me a decent rental lol.

Haha, I know. The reality is I just don't want that sort of capital tied up, I can do more exciting things with it. If I were to buy property it'd more likely be cheaper investment properties.

Find me a decent rental lol.

I don't do rentals. I wish to make money :huh:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...