Jump to content
SAU Community

Recommended Posts

shane gets around with the guys

he`ll be more then happy to help you out

shane only likes em when they're young :bunny:

:)

i keep getting pwned every day about that crap

i'll get yas back one day :O

ahh thats all harmless we mum goes out anywhere wiht me we are in the 200 cause I don't like her car :) its too slow (well so is the 200 but looks nicer)

ha ha ha mum wanted to go with me cos she said I drive like a lunatic... ha ha ha

Her definition of lunatic=doing the speed limit without hazard lights on sitting away from the steering wheel so u dont hit your chin on the steering wheel

yeh

we're strugglin to make 220kw's from it

when apparently they can make 230-250kw's

bawahahahaa

dan took the pipin off to the turbo the other wk

they haven't properly bored it out like they are suppose to

see now john if u had urself a working gtr, ud be able to get 260awkw out fo the stock turbo's :)

P.S emphasis on the working :O

says the man driving around in a SUBARU

id rather walk/catch trains than be seen in one of them :)

fine with me, you can walk then bitch! its still going faster than your gtr right now :O

i keep getting pwned every day about that crap

i'll get yas back one day :laugh:

no, no you wont :bunny:

:laugh:

yes sorta like mine "and look out there is a car turning...." its a good 40m away sometimes it is frustrating driving with her but well its your mum you can't stay mad at her.

well I am off to dans I will talk to everyone later and if a group want to meet up tonight for something to do pm me as I would like to.

yes sorta like mine "and look out there is a car turning...." its a good 40m away sometimes it is frustrating driving with her but well its your mum you can't stay mad at her.

well I am off to dans I will talk to everyone later and if a group want to meet up tonight for something to do pm me as I would like to.

ha ha ha exactly.. the commentary while driving is priceless bless their lil hearts!

Have a good one :) Nice talkin to ya

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...