Jump to content
SAU Community

Recommended Posts

I've got an R33 GTST s2, stock except for exhaust. It's done 100,000km.

This only happens if I boost it a little bit (i.e. the turbo gets hot, I assume), and then I let it cool down some, and put the throttle down 'enough' to get some air going through the turbo (say 0psi or more on the boost guage, I guess). It might only take a few minutes of idling to get 'cool enough' to make the noise, or I could have left the car off for an hour and start it up, and it's there.

The noise is a high, constant pitch whine. It goes away once the turbo warms up again.

I've asked mates, nobody seems to have a clue, and searches didnt turn up anything.

Help much appreciated :)

doesnt Nissan say that at around the 100k mark Turbo should be rebuilt or replaced

The manual doesn't specify... this would be good to know.

It would probably be better to replace the turbo than have it rebuilt, no? Few hundred for a used one, hate to think how much labor would be for a rebuild...

GCG highflow $1900 for them to do your turbo, buts that you taking it off and sending it to them. Its not taht hard to take your turbo off, just fiddley and time cosuming (especialy if you snap any bolts), good luck. The turbo could last another 100k but who knows. It might not even be the bearings making the noise, have checked all your hose connections make sure there not loose.

I had similar problem, whinning noise when on boost. turned out to be leaking connection between return pipe and stock cooler. only realised this when it blew the dam thing off one night. check all ur piping connections probly just air escaping somewhere

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...