Jump to content
SAU Community

Recommended Posts

Hey guys,

Kind of silly n00b question, but im stuck, where do i begin modding my car,

Essentially i want the car to slide well (drift), but do i start with power or handeling?

The car is completely stock bar the front strut bar and a pod, should i go for exhaust or coilovers?

Any suggestions?

Cheers

(sorry for the n00b question........)

Link to comment
https://www.sau.com.au/forums/topic/120054-4-door-r32-gts-t-mods/
Share on other sites

Good to hear. I have a 4 door gtst 32.

If you want to drift a good choice is the suspention. Coilovers all around.

front mont cooler and then you can up your boost a bit.

17" wheels are better than the standard for drift, they also look far better.

you also will need to lock/remove your HICAS (rear steering) because drifting will become hard with any speed.

Mal

Edited by wal

(sorry for the misplacement of topic.... may bad)

Thanks for the info, i was leaning toward suspension, i was planning on teins and a hicas lock kit, looks like that will be my next mod!

I guess in the early learning stages power isnt important its more about technique and set up.

Thanks man.

:(

Yeah mate if you're heading for drift a set of coilovers with 8kg front, 6kg rear spring rates. Pretty good balance for a daily driver.

Make sure to get a Hicas lock BAR. As some kits only add washers to the hicas mechanism.

If you can handle a bare boot> Strip it bare.. There's a good 20-30 kgs kg's in there.

After the suspension is sorted you should really look at a good mechanical LSD. But if the stocker is in reasonable nick you could probably get away with it for a few months(cause I know stock exhausts suck). If you're really cheap you can get it 'Shimmed up'. But they rarely last more than a year after that.

That was another question i was going to ask was spring rates, thanks Drift limo!

Shimming up the diff sounds like it will cost more in the long run, what are your guys opinions on KAAZ diffs???

The lock bar is def going in, hicas is annoying :D

Should i be installing sway bars with the coils and camber arms?

Cheers guys

I have a R32 sedan which I use to compete with in Perth. The basic mods I started off with was a catback exhaust, pod filter, hicas lock, front and rear strut braces and a set of coilovers. Which I found was more than enough to start drifting on. Since then I have added pineapples, GTR skyline rear swaybar (enables slightly more oversteer), a cheap spring type boost controller and a FMIC. If I had my time again I would spend the money on buying a decent FMIC kit, preferably one which has 'switchback' piping (comes in at the right and goes back the same way) because it will for one allow you to put in a decent size oil cooler in a convinent location and also avoid the heatsoak that the piping recieves through the crossover piping (which pretty much render's the FMIC pointless).

There is no need for 17" rims or tyres. I drift on stock GTS-T rims 205/55R16's front and rear with the rears sets set to 45 psi. However if you already have them good grip front tyres are definately a necessity. Before you go drifting on the track remove your rear seat and spare tyre and then you should be able to fit 4 rims with tyres in the area where the back seat was with ease.

Having more power always helps.. but its pretty pointless if you can't use it effectively due to lack of driver skill or suspension setup. Stock power with a catback exhaust and a pod is more than enough to start off with. Allows you to drift with your foot flat as well most of the time which makes it easier to drift on.

So in your position I would say lock the HICAS as a first priority then find some coilovers and then an exhaust. And this should be more than enough to get you started.

Oh yeah make sure your handbrake is adjusted properly as well.

Cheers,

Baz, this will sound wierd but ive sen you slide at wanneroo and your the reason i got a four door.

What youve just said makes mucha sense, looks like ill be doing that switchback idea too!

Thanks for the input guys, it will be put to good use!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...