Jump to content
SAU Community

Racing Chip For R33


Recommended Posts

i have been told that to make my R33 GTS that bit faster i can install a "racing chip"

Does anyone have any experience with what type of chips work the best and how much they are.

thanks

Link to comment
Share on other sites

i was going to make the same topic about a racing chip 4 my r33

my mates have been telling me to install a chip

but i have no idea who does it wat brand i should use and how much it would cost so if anyone could help in this thread it would be great

Link to comment
Share on other sites

you are better off getting a chip burnt or safc tuned for your specific car than installing a one size fits all chip. alot of the chips out of japan are not good for australian fuels because they are tuned for 101 octane fuel. the jap ones run too much ignition timing and are often dangerous.

Link to comment
Share on other sites

Given that its NA and you're probably not running a stripped down engine, I'd look at a piggyback. At a bolt-on level of tune the gains from going to a standalone ECU aren't worth the cost.

A'PEXi SAFC, Unichip (if they make one for your RB25DE), or the GReddy eManage / HKS F-Con etc would be fine. You'd then need to get it tuned.

But, as everyone else has said, don't get a "one size fits all" ECU. Its not tuned for your mods, so you'll either not get all the gains you could (which makes it a waste of time and money) or at worst it'll damage something.

If your car doesn't have any other mods, you'd be better off getting a catback exhaust before touching the ECU.

Link to comment
Share on other sites

itll do bugger all. if you could magically reprogram the ecu and suddenly your car noticably better for racing then that would be so lovely, but if you could make the car that much better with the ecu alone, nissan would have made it like that. itll hardly make your car faster, it probably wont change you laptimes around a track etc. if you don't know that much about cars you probably wouldnt even notice a difference. to get more power out of an na 33 takes money, and you WONT get easy gains like a turbo car. you could put a full exhaust system on and make less power. you might make more. it might stay the same. Turbo it or spend $$$$$ making the RB25DE go harder (still not as hard as a turbo) OR....spend your money on things that will noticably make your car better for "racing", depending on your idea of the term..... (not the red light variety). My meaning would involve actually driving round corners.

For an NA 33, in order of how much it will improve your speed.

1. Driver training - skidpans/trackdays/motorkhanas/anything that involvers performance driving with tuition/supervision. That, and developing your understanding of the mechanics/dynamics of a car.

2. Suspension

3. Brakes

Helpful note: People that say "you should put a racing chip in it" have no idea, or are making fun of you. And if you are talking to someone who knows cars and you say that your 33 GTS has a racing chip you're going to look like an idiot.

Link to comment
Share on other sites

on my NA 300zx i gained 22rwkw just from SAFC tune. no ignition timing increase. the reason nissan could not make their cars with the "ideal tuning" is because they have to run everything very safely because alot of people don't look after their cars. look at how rich factory ECU's run. NA 300zx's ideal A/F ratio is around 12.8:1, i imagine this would be not too dissimilar to NA skylines. my car before tuning was running at 10.5:1. it will make your car go faster, it will change your lap times, you will notice the difference, and you will save noticeably on fuel. it will make the car nicer to drive daily with more low-mid range torque. yes brakes and suspension are important, but i doubt that he is talking about racing his car on the track, more likely he is just using the term "racing chip" as a descriptor for modifying the ECU settings.

itll do bugger all. if you could magically reprogram the ecu and suddenly your car noticably better for racing then that would be so lovely, but if you could make the car that much better with the ecu alone, nissan would have made it like that. itll hardly make your car faster, it probably wont change you laptimes around a track etc. if you don't know that much about cars you probably wouldnt even notice a difference. to get more power out of an na 33 takes money, and you WONT get easy gains like a turbo car. you could put a full exhaust system on and make less power. you might make more. it might stay the same. Turbo it or spend $$$$$ making the RB25DE go harder (still not as hard as a turbo) OR....spend your money on things that will noticably make your car better for "racing", depending on your idea of the term..... (not the red light variety). My meaning would involve actually driving round corners.

For an NA 33, in order of how much it will improve your speed.

1. Driver training - skidpans/trackdays/motorkhanas/anything that involvers performance driving with tuition/supervision. That, and developing your understanding of the mechanics/dynamics of a car.

2. Suspension

3. Brakes

Helpful note: People that say "you should put a racing chip in it" have no idea, or are making fun of you. And if you are talking to someone who knows cars and you say that your 33 GTS has a racing chip you're going to look like an idiot.

Link to comment
Share on other sites

Yes you right cookie300zx, im not gonna race on the track against other Skylines because i will probably have my arse handed to me, but hey gotta start somewhere right. I was meaning having the ECU modified. What is with the different geear ratios eg 12.8:1 & 10.5:1, what does that mean in plain english?

Link to comment
Share on other sites

he's not talking about gear ratios...

he's talking about AFR (air to fuel ratio)

basically its air:fuel

a 12.8:1 ratio means that the mixture going into the motor has 12.8 times more air (mass) than fuel

Link to comment
Share on other sites

on my NA 300zx i gained 22rwkw just from SAFC tune. no ignition timing increase. the reason nissan could not make their cars with the "ideal tuning" is because they have to run everything very safely because alot of people don't look after their cars. look at how rich factory ECU's run. NA 300zx's ideal A/F ratio is around 12.8:1, i imagine this would be not too dissimilar to NA skylines. my car before tuning was running at 10.5:1. it will make your car go faster, it will change your lap times, you will notice the difference, and you will save noticeably on fuel. it will make the car nicer to drive daily with more low-mid range torque. yes brakes and suspension are important, but i doubt that he is talking about racing his car on the track, more likely he is just using the term "racing chip" as a descriptor for modifying the ECU settings.

if u take a closer look how SAFC works, u are advancing the ignition timing when u lean it down

Link to comment
Share on other sites

if u take a closer look how SAFC works, u are advancing the ignition timing when u lean it down

cuold you explain that in more detail please. my base timing is set at 15 degrees (stock for 300zx NA) so could you explain how the ignition timing is being advanced by leaning out the AF ratio?

Link to comment
Share on other sites

I saw a "LAP" chip for an rb25de on just jap's used electronics section

maybe this is the kind of thing you're after?

http://www.justjap.com/parts_uelectronics.htm

those are the things i was saying you should not be buying. would be tuned for JAP fuel, and you have no idea what the AF ratios and ignition timing would be set at! could be rather dangerous, and you won't get the same gains as a chip/piggy back that has been tuned for your car

Edited by cookie300zx
Link to comment
Share on other sites

Personally i think if your going to keep your NA for a while and you love your car it can be a good idea to go for an ecu tune.

If your just going to do simple mods like exhaust&intake mods I would expect that you could certainly expect more power from getting your ecu modded.Put it this way, on my rb20de with 2 1/4 inch exhaust and k&n pod i made 85kw@wheels. Then the timing was advanced just a few degrees and it consistantly jumped up to 89rwkw's. When they mod your ecu they will generally change both your fuel and ignition maps together. If your going to run 98ron fuel all of the time then they would likely advance your timing right throughout the rev range as well as lean out your afr's a bit depending what they look like. I would say you could get maybe 6 or 7rwkw's out of it if it was done well.But thats just a rough estimate. wouldnt expect to much more than that.

The place im getting my rb20 ecu tuned for my turbo setup doesn't do rb25 ecu's yet.

Ohh and my old u12 pinny ka24e made 3.8fwkw's more after just timing advance so it gives you an idea of the extent of which tuning will effect the power of your NA.

Link to comment
Share on other sites

  • 4 weeks later...

I have a rb30... Im yet to work out what it has done except add about 5rwkw. Tested it on a dyno but i just cant work out what it changed! Fuel consumption has stayed roughly the same and as far as i can tell the timing hasnt changed... The car runs a little smoother and i was told it would help elliminate any dark smoke but I didnt have much in the first place. Picked it up for $40 so i thought id give it a go.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • So after some Chat GPT (yeah I know lol..) it turns out that the R35 GT-R BMC conversion may not be suitable for our shit boxes as it splits the fluid 60:40 instead of 70:30. When looking at possibly doing the 370Z conversion, it seems it's quite similar to how the R35 GT-R booster & BMC mounts up, however after some additional digging the 370Z BMC bore is the same size as a R33/34 GT-R BM57 one. Brake Pressure Split: Nissan 370Z: The typical front-to-rear brake pressure ratio for the 370Z is approximately 70:30. This is designed to handle the car’s weight distribution and performance characteristics, favoring the front brakes heavily due to weight transfer during braking. Nissan R33 GT-R: The front-to-rear brake pressure ratio for the R33 GT-R is also typically 70:30. However, this ratio is tuned for the GT-R's specific weight distribution and dynamic performance, considering its all-wheel-drive system and higher performance expectations. Despite having the same nominal 70:30 ratio, the actual distribution of braking force in practice can be different due to other factors like vehicle weight, ABS and EBD systems, and brake component sizes. Bore Sizes: The bore size of a brake master cylinder affects the hydraulic pressure generated within the braking system and can vary between different vehicles based on their braking requirements. Nissan 370Z: The brake master cylinder typically has a 1-inch (25.4 mm) primary bore. The secondary bore can vary slightly depending on specific trim levels and brake options, such as the Nismo version or those equipped with the Sport Package which features larger brakes. Nissan R33 GT-R: The brake master cylinder in the R33 GT-R generally has a 1-inch (25.4 mm) primary bore as well. Given the GT-R's high-performance context and advanced braking system, the bore size is designed to provide sufficient hydraulic pressure for its braking needs. Comparison: Brake Pressure Split: While both vehicles use a similar 70:30 ratio in the brake master cylinder design, the actual operational distribution might differ slightly due to differences in brake system components, vehicle dynamics, and tuning for each model. Bore Sizes: Both the 370Z and R33 GT-R use a master cylinder with a primary bore size of around 1 inch (25.4 mm). This similarity helps in providing robust hydraulic pressure for effective braking. Additional Considerations: Braking System Design: The overall brake system, including calipers, rotors, and the master cylinder, is designed to work as an integrated unit. Even with similar bore sizes and pressure splits, the performance and feel of the brakes can differ due to variations in brake pad composition, rotor size, and ABS tuning. ABS and EBD: Both vehicles are equipped with Anti-lock Braking Systems (ABS) and Electronic Brake-force Distribution (EBD), which further modulate and optimize braking force between the front and rear wheels dynamically, depending on driving conditions and brake demand. In essence, while the 370Z and R33 GT-R have some similarities in their brake master cylinder specifications, they are tuned to meet the specific performance and handling characteristics of each vehicle.   TL;DR, just use a R33 BM57 and call it a day.
    • Straight thru's have so little restriction that it's almost certainly not worth worrying about effects on tuning. Even a centre offset shouldn't upset things, but would be noticeably more effective (quiet).
    • I did say "2x Magnaflows" then referred to a Varex. So to un-confuse that, my rear muffler is hot-swappable with a Varex. When I had a RB Turbo, I had the 2x Magnaflows, then went LS and though "Oh that's way too loud" and ordered a Varex. A mid muffler will definitely help a lot, even if straight through. SP Mufflers can make anything as big or as small as possible, which will help even more. Looking at my own exhaust I could make the muffler twice as long if I wanted to. Or you could go crazy and get 2x mufflers from SP and full every remaining space with muffling. In my experience closing the Varex makes the car run VERY rich (obviously). I'd say adding a muffler *will* affect things, on a technical, physics level, but I don't think you'd need a retune as the actual effect would be the car running a *tiny* bit richer due to more restriction, on a strictly physics level, but you kind of don't have any option if you want the car to make less sound.
    • I must have read 100 DIY's and watched 200 DIY Youtube videos with most people saying just grab a new cover and, well, despite my normal aproach to these things (replace it all!!) I didn't get a cover. I don't know why I didn't, I'd already ordered a bunch of bits from FCP and it would have made perfect sense to put that in the order.  Anyway, I'm not getting OEM as its just crazy money, even from the states its 900 ish delivered. So, I got an OE Elring one, same as they sell at FCP but local so I can get this fixed this week. Our X5 is waiting for a new diff so we find ourselves in a common scenario of having 2 broken BMW's on the driveway! 🤣
    • Big thing is available inputs for sensors and not having to run multiple expander boxes and software packages for different things why motec is up there. The link ecu and an aim pdm32 was a combination I looked at early on so get ecu, dash and pdm in one go. Aim logging software is pretty good and has all the tracks I will ever drive. Having logging setup with tracks already available is a big thing for myself so can click drop down and go. Thing that I keep seeing is the support what's needed and having a package that people in the know are familiar with as learning a new platform is time consuming.    Got a few boxes that arrived with bits while I was away so hopefully will fit a few sensors and make a start on the dump pipe today. Going to be interesting fitting a 3.5 inch exhaust on this and keeping it above the chassis rails. 
×
×
  • Create New...