Jump to content
SAU Community

Fuel Injector Insulators Needed! - Found!

PHATR32

By PHATR32,
in Western Australia

 Share

Recommended Posts

PHATR32 Grand Master

PHATR32

Posted
Posted (edited)

hey guys,

im after a set of insulators and O rings for the fuel injectors in my gtr.

Im too scared to call nissan up, as i dont wanna sell my kidney's to get the parts.

would a fuel injector place have aftermarket insulators in stock?

thanks

steve

Edited by PHATR32
PHATR32 Grand Master

PHATR32

Posted
  • Author
Posted

oooooooookkkkkkkkkkkkkaaaaaaaayyyyyyyy

i just called a "injector speicalist" in balcatta, and he had no idea of what i was talking about. he told me the insulators had to get pressed?? I think he's been breathing too much fuel......

can anyone reccomend me someone who knows what im talking about??

steve

Scradly Community Regular

Scradly

Posted
Posted

The guy at the injector place is right. The insulator pressed onto the injector and its black if i remember. Why do you need 12 when there is only 6 injectors or do you mean 6 insulators and 6 orings.

I would ring that injector place back and take them down there so they can have a look.

PHATR32 Grand Master

PHATR32

Posted
  • Author
Posted
' date='8 Jun 2006, 12:08 AM' post='2237932']

when i went to nissan i got o-rings.. 2size one big, one smaller

thats all i needed for my nismo injectors

Thats probly cuase you have side feed injectors. The gtr has top feed, and it uses only 1 O ring, and 2 insulators to basically hold it in place.

I just rechecked my injectors and i actually need only the bottom insulator.

here is a pic of the gtr injectors. post-11604-1149726849.jpg

Steve

Scradly Community Regular

Scradly

Posted
Posted

Ok now i know what you mean. Its the black rubber grommet that sits in the head.

I would still go to an injector place or you are goin to have go to nissan to get them.

I work for nissan but im on workers comp now so im unable to help dude. sorry

PHATR32 Grand Master

PHATR32

Posted
  • Author
Posted

yeah no worries man.

i might pull the injectors out sat morning, and take one down.

they look exactly the same as the ones in my old laser, although the sizes might be differant.

Im sure i can find them for cheaper else where, after all, it is a small rubber ring.

steve

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...