Jump to content
SAU Community

Recommended Posts

Typical Canberra day - cold and wet with very slippery roads. All sorts of cars, and drivers sliding everywhere.

Funny thing is you get some real 'dirty' looks as you merrily flash past in the Stagea - AWD and you are gone, grip, grip, grip, fun, fun, fun

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/
Share on other sites

funny you should post that - its raining here for the first time in two months, and this morning i went out and did everything in my power to intentionally BREAK traction... lol had some fun, love it.

good times.

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2245028
Share on other sites

stageas are alright sideways, just need a big enough area.

awd makes for some good sideways action, but open rear diff doesnt. Must balance the two.

Also, my issue is i hit the limiter in 1st too quickly. I dont like getting sideways in D and so i leave it in 1, but then i hit the limiter too quickly and then slow down etc. ... must.... buy..... manual.... stagea

Bloody 260RS's, manual AND LSD'ed up :)

BTW, in the wet i always get this

Stall... launch.... beat other car... next lights

"IS THAT 4wd??!?!?!??!?!??!?!??!!"

Im like, yeh, hahah

Interstingly enough, if i nail it sometimes just driving forwards and the road is on a slight tilt and a bit wet/dirty, i loose the rear and start fishtailing.... (i think ive taken stagea beyond what it was designed for :P)

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2245038
Share on other sites

hmm you'd be able to get an LSD centre though, right? might look into that.

and yes, breaking the rears loose under those conditions probably means that youre exceeding the boundaries of said stagea, dude. noice one.

with stageas, does it start off with most pwr to the rears, then gradually feed more to the fronts when it detects traction loss ie. difference in rotation speeds front and back? or is it a constant thing? cos i know my cars whips right out, spinning crazily at the back, bouncing off 7K, then the front start to spin and pull, and the rear swings back, so i figured that may be the case.

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2245143
Share on other sites

Yes, but rpm limiter launch + wet road = 4wd spin for me :P

Very scary having your car suddenly jump sideways!!!

But yeah I can easily break traction in the wet, in the dry I havent been able to.................. yet.

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2245336
Share on other sites

I'm starting to enjoy the occasional sideways slide, but am really hanging for when I can afford a skid-pan day so I can explore my car a bit further.

Up till now, I've never really had the run-off room to feel comfortable sending my car sideways, and I never do it when there are other cars around just-in-case.

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2246088
Share on other sites

Guys NO ONE should be doing anything like this on the road.

Skylines Australia does not allow the disscussion of performing such activities on public roads, because it is illegal and might lead to future litigation.

We dont want this thread to dissapear like the "Blown Away" thread now do we :P

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2246693
Share on other sites

Drove the Stagea in the wet for the first time today, seems pretty much idiot proof to me, I guess if you get one sideways you're already being "really silly", so something could go wrong in a big way... Would be a great first car for young guys/girls, definitely save a few telephone poles along the way too! Or maybe the limit of traction is too far out there and would provide over confidence? Any comments welcome, moving this thread in a positive direction possibly...

Cheers

Luke

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2247508
Share on other sites

Oh mate, this is my first car (that got on road) and yeh, DEFINATLY a great first car.

The only downside i see to it is understeer in the wet. With my old nankangs the bitch used to understeer going around the corners with mild speeds. The K104's have really improved that now and it has no real issues (unless i cause them >_<)

Ive told my best mate over and over, if i was to buy a first car for my kid that was turbo, id have to choose the stagea.

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2248262
Share on other sites

Over here in NZ there has just been a huge dump of snow in the South Island. 6"+ down to sealevel! Unfortunately, I live in the North Island. I want to go to the South Island to drive the wagon in the snow!!!

Wet roads are boring in the Stagea, although since no one knows the car, they all think you must be a good driver to take the corner at that speed and not slide.

The Stagea makes you look good in bad weather.

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2252569
Share on other sites

Have driven a stagea in the snow - my own. Some of you may know i bought it off my family in japan. we took it for a drive from tokyo to about 50km north of Sendai to go snowboarding.

you have to ktae it slow, of course, and drive on the rougher patches where it isnt quite too slippery, but it went fairly well, in "snow mode", and no mishaps or even close calls. was still very nervous the whole time though.

Link to comment
https://www.sau.com.au/forums/topic/121697-wet-and-cold/#findComment-2252605
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity.
    • 100% the factory sender is tapered, that is how it seals (well, that and teflon paste or tape)
    • Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
×
×
  • Create New...