Jump to content
SAU Community

Recommended Posts

Hey guys 'n' gals,

I am looking at putting a set of 19x8.5" with 234/245 tyres on the front, and 19x9.5" and 255/265 tyres on the rear to a GTS-T R33... Is this possible with maybe only lippping, or would some more extensive mods need to be made? Or what offset I would need? I looked through all the page of the "wheel sizes and rim offset for skylines" thread but no-one had listed as putting 19's on there R33.

If anyone knows I would appreciate the info.

:yes:

-Luke

Edited by muaythailuke
Link to comment
https://www.sau.com.au/forums/topic/122147-19s-on-a-r33-gts-t/
Share on other sites

Not sure about the offset and everything but one of my mates had a 33 and he was running 265 on the back and 245 on front no worries, not scrub, nothing

Cheers man, yeah im running 245 on the front and 265's on the rear now but only in a 17x8 and 17x9 rim and ive been told buy some that I cant run a 19x9.5 on the rear I was just wondering if anyone could confime this?

:yes:

shit just re read and u said u already got 265! Yeah width obviously not a problem if you already got them on there! Prob be bit more worried about the 19" though not quite sure as i got 32! My mate had 18x9 on back with 265! Though few people on here i seen running 19x10..though guessing serious mod for that

18x9.5 impuls definately fit inside stock R33 GTS-t guards, and the car can be lowered several inches without rubbing.

a mate had them on his R33. I would presume the 19s wouldnt be any different.

Edited by _8OO5TED_

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...