Jump to content
SAU Community

Recommended Posts

Hey guys

Have done some searches is regards to this but can’t find anything that really answers my question. I have only used a tank of this and have to say that this fuel is excellent. :D My car has never gone so good, its like I’ve boosted it up. Much quicker power response and smooth power right up to red line.

I have done a little reading but convinced my self to only use it say for weekend use or every few tanks.

What needs to be done to run this stuff everyday every time in a skyline or you can run it with no problems.??

fill it up with the extreme shit, and chuck the car on the dyno and get it tuned for that fuel

yeah sweet ,if that's all that is really needed. I've been told being ethanol I would need to change my fuel lines and some other stuff. So it that all crap.

Has anybody else experience a power increase like my self??

As posted elsewhere (tip = try a search before you start a new thread)

We have been using Shell Optimax Extreme 100 ron exclusively since it became available in Sydney in the R33GTST. It has a PFC running the default ignition timing which knocks noticeably (dash warning) on 98 ron. In several months running the 100 ron we have not seen any dash warnings and the logged knock levels are less than 20. I have modified the injection maps for a target A/F ratio of 12 to 1.

I have heard all of the ethanol stories, eats fuel lines, blocks injectors, roots fuel pumps and gives your unborn two heads. So I have pulled the injectors a couple of times, checked the flow rates and guess what? No changes. Also I have cut the last 3 fuel filters open and guess what? No decomposed fuel hoses in there either. We also log fuel pressure and guess what? The fuel pump is showing no signs of dying. Sorry, I can’t test the unborn baby theory.

I have checked with everyone that I now who is running Shell Optimax Extreme 100 ron in their Skyline and I have yet to find anyone who can report eaten fuel lines, clogged injectors, blocked fuel filters or failed fuel pumps.

My suggestion, get on with it and reap the benefits.

:D cheers :D

Edited by Sydneykid
We have been using Shell Optimax Extreme 100 ron exclusively since it became available in Sydney in the R33GTST. It has a PFC running the default ignition timing which knocks noticeably (dash warning) on 98 ron. In several months running the 100 ron we have not seen any dash warnings and the logged knock levels are less than 20. I have modified the injection maps for a target A/F ratio of 12 to 1.

Do you know what was causing it to excessively knock even using the default ignition timing?

As posted elsewhere (tip = try a search before you start a new thread)

We have been using Shell Optimax Extreme 100 ron exclusively since it became available in Sydney in the R33GTST. It has a PFC running the default ignition timing which knocks noticeably (dash warning) on 98 ron. In several months running the 100 ron we have not seen any dash warnings and the logged knock levels are less than 20. I have modified the injection maps for a target A/F ratio of 12 to 1.

I have heard all of the ethanol stories, eats fuel lines, blocks injectors, roots fuel pumps and gives your unborn two heads. So I have pulled the injectors a couple of times, checked the flow rates and guess what? No changes. Also I have cut the last 3 fuel filters open and guess what? No decomposed fuel hoses in there either. We also log fuel pressure and guess what? The fuel pump is showing no signs of dying. Sorry, I can’t test the unborn baby theory.

I have checked with everyone that I now who is running Shell Optimax Extreme 100 ron in their Skyline and I have yet to find anyone who can report eaten fuel lines, clogged injectors, blocked fuel filters or failed fuel pumps.

My suggestion, get on with it and reap the benefits.

:D cheers :D

Hey Sydney Kit

yeah I did do a search but nothing really quenched my thirst for the questions I had.

Maby I didn’t look hard enough.

But your info SPOT ON!! :D thank you for that, that’s all I really needed to hear.

Thanks

I think it was to try to make the ethanol industry in Australia viable. But my dad told me the other day that the government is pulling out of the ethanol industry and they're gonna source it from overseas.

Really doesnt help the struggling sugar cain farmers up north. Good on you johny.

So why isnt optimax extreme cheaper than regular 98 octane optimax, if it has ethanol in it?

Wasnt that the whole point of having ethanol in fuels?

No, the government doesn't believe in free trade. They tariff the shit out of cheap Brasilian stuff to protect our own industry... which we didn't have till Johny made one for his school chums.

So.. that's why it ain't cheaper.

As posted elsewhere (tip = try a search before you start a new thread)

We have been using Shell Optimax Extreme 100 ron exclusively since it became available in Sydney in the R33GTST. It has a PFC running the default ignition timing which knocks noticeably (dash warning) on 98 ron. In several months running the 100 ron we have not seen any dash warnings and the logged knock levels are less than 20. I have modified the injection maps for a target A/F ratio of 12 to 1.

I have heard all of the ethanol stories, eats fuel lines, blocks injectors, roots fuel pumps and gives your unborn two heads. So I have pulled the injectors a couple of times, checked the flow rates and guess what? No changes. Also I have cut the last 3 fuel filters open and guess what? No decomposed fuel hoses in there either. We also log fuel pressure and guess what? The fuel pump is showing no signs of dying. Sorry, I can’t test the unborn baby theory.

I have checked with everyone that I now who is running Shell Optimax Extreme 100 ron in their Skyline and I have yet to find anyone who can report eaten fuel lines, clogged injectors, blocked fuel filters or failed fuel pumps.

My suggestion, get on with it and reap the benefits.

:unsure: cheers :yes:

someone from the silvia forums used ethanol based petrol in his old CA silvia, and it caused his rubber fuel lines to expand and eventually caused leaking fuel in certain places. he went back to non ethanol based petrol and its fine again now. so while it may be ok in newer cars, i dont think you should be giving a blank cheque to everyone saying its all good, i would say you should be cautious with it, especially in older cars.

the warning given by manufacturers that older cars shouldnt run it, is probably also something to consider

someone from the silvia forums used ethanol based petrol in his old CA silvia, and it caused his rubber fuel lines to expand and eventually caused leaking fuel in certain places. he went back to non ethanol based petrol and its fine again now. so while it may be ok in newer cars, i dont think you should be giving a blank cheque to everyone saying its all good, i would say you should be cautious with it, especially in older cars.

the warning given by manufacturers that older cars shouldnt run it, is probably also something to consider

:unsure:

And you should read carefully next time. Gary is talking about Optimax Extreme, not just any ethanol blended fuel. He has no issues with fuel line damage with Extreme. I have had similar experiences to his. My pump and lines were tested following a switch to Extreme and had no problems.

:unsure:

And you should read carefully next time. Gary is talking about Optimax Extreme, not just any ethanol blended fuel. He has no issues with fuel line damage with Extreme. I have had similar experiences to his. My pump and lines were tested following a switch to Extreme and had no problems.

no need for funny faces, maybe next time you shouldnt assume, just because i didnt specify which fuel it was doesnt mean it wasnt optimax extreme. to make you happy i'll just add that it was infact optimax extreme 100ron fuel. and im not saying everyone will have problems, im saying its not full proof - and leaking fuel is not a minor concern

so you have proof that the fuel caused the line damage and it wasn't in fact simply the age of the car? or some other reason?

think about it - 5% ethanol in fuel makes up a very small overall volume of ethanol that is in a fuel line at any one time

add to that that ethanol is not corrosive and i don't see the issue

whenever someone has a problem its natural to try to place some blame - i don't think optimax extreme is the answer

i got my gtr lm just before xmas.

mods- exhaust front mount and 14 psi std computer, oil cooler.

i ran 98 in it about 4 times then i changed to opti extreme from the first tank the car immidialtly felt better in drivability and power i have never filled on anything other than opti extreme. since then 25,000km of driving on extreme and couldn't be happier and not a problem whatsoever.....:)

Question is how would you test your lines? Fill up and look? No thanks.

Can I ask if fuel lines are the same material/condition all over the car? If so I might just nick a small piece and drop it into a small container and see what it does to it.

add to that that ethanol is not corrosive and i don't see the issue

Do I take your word for it, or do I take Toyota's?

Toyota, a market leader in petrol-electric hybrid vehicles, has resisted the technology amid worries about the impact of highly corrosive ethanol on rubber seals in the engine, the Financial Times said.

One of you is the second largest car company in the world and the most profitable, with an enviable reputation for reliability and build quality. They would have to replace the damaged parts under warranty should it fail after giving this fuel the all-clear, and if the seals burst and cause a fire they might even be criminally liable (like the old Ford Pinto).

The other is some random bloke of an unknown reputation, with no access to scientific testing or engineering, nor do they have a responsibility to ensure that their advice is safe or accurate.

The thing is, OEMs will err on the safe side. If there's a chance it'll f**k up, they must assume it will. Anyone who's come from a support background will know that the last thing you give someone is choice, because the great unwashed will inevitably choose the wrong one. And due to our nanny state your mistake is their fault.

My 2003 Nissan isn't approved by Nissan Australia to run fuels of any ethanol blend, although cars made in 2003 have gone to countries that use ethanol fuels and I doubt Australia's market is big enough to justify a custom run of vehicles. But, at the same time, I only put Optimax Extreme in right before I hit the track and chances are I've emptied the tank by the end of the day, at which point I put BP Ultimate back in.

I won't say that it'll definitely happen to any car, but if I see threads with people whinging about how their fuel lines / engine seals etc seem to have corroded away after they were using only ethanol-blended fuel for months and months, they can expect a "bwahahaha, sucks to be you" response. You were warned by the guys who make the car, and you chose to ignore it. Maybe based on Sydneykid's advice and his own testing you can sue him for the damage to your vehicle, but good luck with that.

Do I take your word for it, or do I take Toyota's?

One of you is the second largest car company in the world and the most profitable, with an enviable reputation for reliability and build quality. They would have to replace the damaged parts under warranty should it fail after giving this fuel the all-clear, and if the seals burst and cause a fire they might even be criminally liable (like the old Ford Pinto).

The other is some random bloke of an unknown reputation, with no access to scientific testing or engineering, nor do they have a responsibility to ensure that their advice is safe or accurate.

The thing is, OEMs will err on the safe side. If there's a chance it'll f**k up, they must assume it will. Anyone who's come from a support background will know that the last thing you give someone is choice, because the great unwashed will inevitably choose the wrong one. And due to our nanny state your mistake is their fault.

My 2003 Nissan isn't approved by Nissan Australia to run fuels of any ethanol blend, although cars made in 2003 have gone to countries that use ethanol fuels and I doubt Australia's market is big enough to justify a custom run of vehicles. But, at the same time, I only put Optimax Extreme in right before I hit the track and chances are I've emptied the tank by the end of the day, at which point I put BP Ultimate back in.

I won't say that it'll definitely happen to any car, but if I see threads with people whinging about how their fuel lines / engine seals etc seem to have corroded away after they were using only ethanol-blended fuel for months and months, they can expect a "bwahahaha, sucks to be you" response. You were warned by the guys who make the car, and you chose to ignore it. Maybe based on Sydneykid's advice and his own testing you can sue him for the damage to your vehicle, but good luck with that.

I suggest you ring Toyota and ask them;

Do they mean 100% ethanol?

Or 10% ethanol?

Or 5% ethanol.?

They (like Nissan) are conveniently vague and simply lump all ethanol fuels into one bucket. And any chemical engineer will tell you that is technically incorrect. They are simply saving their ass from any possibility (no mater how small), that one of their customers somewhere in the world might use 100% ethanol and have a problem. Remember this is not an Australian edict, it’s WORLD WIDE. So they have to take into account the most extreme cases in 3rd world countries where some guy will boil up a pot of sugar cane and poor it into his Camry.

Think about what we are discussing here. Ethanol supposedly eats stuff from the in side out. If this was happening, then I could see it in the fuel filter when I cut it open. Or in the injectors when I clean them. I don’t, haven’t in the R33GTST for almost 6 months, that’s 1,300 litres or ~30 full tanks full of Optimax Extreme.

I have tested it, I haven’t found a problem. If you are afraid, then test it yourself. If you don’t want to do that, then don’t use it. It is that simple.

:) cheers :D

They (like Nissan) are conveniently vague and simply lump all ethanol fuels into one bucket. And any chemical engineer will tell you that is technically incorrect. They are simply saving their ass from any possibility (no mater how small), that one of their customers somewhere in the world might use 100% ethanol and have a problem.

The data Toyota Australia has supplied to the Australian Federal Chamber of Automotive Industries is pretty specific. If I called them, I'm sure they'd refer me to Read The Friendly Message they sent to the FCAI.

So they're not thinking about some rogue sugar cane farmer in Far North Queensland pouring the stuff the Bundy distilleries won't buy into his Land Cruiser or Patrol when they came up with their guidelines.

And Nissan is just as specific on their guidelines pertaining to up to a 10% blend. Any Nissan they've brought in prior, in their book, shouldn't. And they don't recommend running more than E10.

As for grey imports, Nissan Australia has always washed their hands of them so perhaps Nissan Japan built R33s with an ethanol-using market in mind.

Anyway, if it works for you that's great. And if any OEM can guarantee you quality control in their manufacturing process (and that of all their component suppliers) that's 100% consistent, making your test proof positive that it will work for every other owner out there, then everyone else should be safe despite Nissan's due consideration and testing (which may or may not apply to you).

As I said, my car is pre-2004 and I use Optimax Extreme. But I'm under no illusions that it'll be a-OK and I can reasonably complain to get it fixed under warranty should it go wrong and the fuel blend is to blame.

The data Toyota Australia has supplied to the Australian Federal Chamber of Automotive Industries is pretty specific. If I called them, I'm sure they'd refer me to Read The Friendly Message they sent to the FCAI.

So they're not thinking about some rogue sugar cane farmer in Far North Queensland pouring the stuff the Bundy distilleries won't buy into his Land Cruiser or Patrol when they came up with their guidelines.

And Nissan is just as specific on their guidelines pertaining to up to a 10% blend. Any Nissan they've brought in prior, in their book, shouldn't. And they don't recommend running more than E10.

As for grey imports, Nissan Australia has always washed their hands of them so perhaps Nissan Japan built R33s with an ethanol-using market in mind.

Anyway, if it works for you that's great. And if any OEM can guarantee you quality control in their manufacturing process (and that of all their component suppliers) that's 100% consistent, making your test proof positive that it will work for every other owner out there, then everyone else should be safe despite Nissan's due consideration and testing (which may or may not apply to you).

As I said, my car is pre-2004 and I use Optimax Extreme. But I'm under no illusions that it'll be a-OK and I can reasonably complain to get it fixed under warranty should it go wrong and the fuel blend is to blame.

I must be having a dumb day, I don't understand what it is you are are trying to say.

Lets go though the potential problems as listed on http://www.fcai.com.au/ethanol.php/2006/04/00000005.html

one by one;

Vehicles with carburettor fuel systems may experience hot fuel handling concerns. This is because the vapour pressure of fuel with ethanol will be greater (if the base fuel is not chemically adjusted) and probability of vapour lock or hot restartability problems will be increased.

I have not experienced this problem, since R32/33/34’s are fuel injected I doubt that we ever will

As a solvent, ethanol attacks both the metallic and rubber based fuels lines, and other fuel system components.

I have checked this in the 1 X R32GTST, 2 X R32GTR’s, 1 X Stagea RS4, 1 X R33GTST and 5 Hondas. Not a sign, fuel filters and injectors are perfect.

Ethanol also has an affinity to water that can result in corrosion of fuel tanks and fuel lines. Rust resulting from this corrosion can ultimately block the fuel supply rendering the engine inoperable. Water in the fuel system can also result in the engine hesitating and running roughly.

Since R32/33/34’s run closed fuel systems, via the carbon canister, hygroscopic action is virtually impossible. Water in the fuel from a service station can occur regardless of whether it contains ethanol or not

Fuel Injected Engines

In addition to the issues mentioned above for carburettor equipped engines, the use of ethanol blended petrol in fuel injection systems will result in early deterioration of components such as injector seals, delivery pipes, and fuel pump and regulator.

I have checked this in the 1 X R32GTST, 2 X R32GTR’s, 1 X Stagea RS4, 1 X R33GTST and 5 Hondas. Not a sign, fuel filters and injectors are perfect.

Mechanical fuel injection systems and earlier electronic systems may not be able to fully compensate for the lean-out effect of ethanol blended petrol, resulting in hesitation or flat-spots during acceleration.

The cars with Power FC’s actually run better on Optimax Extreme as their base mapping is done for 100 ron fuel. It doesn't seem to have any effect that I can notice on the standard ECU equiped vehicles, and I am trained by experience to feel for even small changes in engine running.

Difficulty in starting and engine hesitation after cold start can also result.

I have noticed this, only on the R33GTST with the Power FC, a slight tweak of the cold start injector dwell fixed it. We have not noticed anything on the standard ECU equipped cars.

Exhaust And Evaporative Emission Levels

Lean-out resulting from the oxygenating effect of ethanol in the fuel may affect exhaust emissions.

I don’t care

Of more concern is that fuel containing ethanol can increase permeation emissions from fuel system components, particularly those that have aged for nearly 20 years. Therefore the increased vapour pressure of fuel with ethanol (if the base fuel is not chemically adjusted at the refining stage) will lead to increased evaporative emissions.

I don’t care

If I have missed something, please tell me what it is and I will test for it. I have all access to all of the gear necessary to check for whatever problem it is you think I should.

:P cheers :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...