Jump to content
SAU Community

R32 4 Door Gte

turboalfa
 Share

Recommended Posts

turboalfa Collaborator

turboalfa

Posted
Posted

Hi,

I just picked up a 4 Door R32 for $4000. It's going to be my daily for a little while then a bit of a budget drifter.

Just want to know what is different with the suspension and rear end/diff.

Can i buy R32 coilovers and what diff should i get? Or should i go for a full skyline/s15etc rear end. Was thinking off keeping the four stud. Any real reason to go 5 stud? Would i break axles with what's in there now?

Sorry for all the questions.

Any help would be greatly appreicated.

Thanks,

Link to comment
https://www.sau.com.au/forums/topic/122711-r32-4-door-gte/
Share on other sites
stricko Enthusiast

stricko

Posted
Posted

As a budget drifter depending on how small your budget is at the least get an LSD. (Limited Slip Differential) a 1.5 or 2 way should do the job. You'll need to stiffen up the suspension so a set of second hand coilovers would do the job. 4 stud is fine but choice of rims can be a bit limited. Axles shouldn't be a concern. A decent clutch wouldn't go astray either for all the clutch kicking you'll be doing. There isn't much else you could do without spending lots of money. Feel free to correct me anyone as i'm only a novice but keen drifter as well.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/122711-r32-4-door-gte/#findComment-2268153
Share on other sites
Green_s13 Proficient

Green_s13

Posted
Posted

the r32 coilovers will fit up fine just make sure you dont get the gtr ones. there is no problem with 4 stud however if you want to change to five stud all you have to do is buy the 5 stud skyline hubs.

i would spend the money on a good lsd makes a big difference, i would also get solid cradle bushes, with the de engine you will need all the suspension help you can get, i would also get some urathane caster bushes.

Link to comment
https://www.sau.com.au/forums/topic/122711-r32-4-door-gte/#findComment-2268499
Share on other sites
turboalfa Collaborator

turboalfa

Posted
  • Author
Posted

Hi,

Thanks for the help.

I'm going to put a RB20DET in eventually. I think drifting 92kw off RB20E will get frustrating very quickly. But just wanted to know about everything else. So it is all the same as a GTS-t except for the hubs and brakes really? So i'm after a R200 diff (with correct half shafts)?

Yeah might put some pineapples in. Is there any other drift neccesities?

Thanks,

Link to comment
https://www.sau.com.au/forums/topic/122711-r32-4-door-gte/#findComment-2268666
Share on other sites
stricko Enthusiast

stricko

Posted
Posted

Just upgrade to the GTS/GTS-T hardware when your current setup breaks. Maybe upgrade the brakes now though. You could also strip alot of the wait out of your car to. That would give the biggest gain to your power to weight ratio and it don't cost nothing either! you can remove the rear seats, carpet, interior panels and all the sound deadening if you really want to.

Link to comment
https://www.sau.com.au/forums/topic/122711-r32-4-door-gte/#findComment-2279296
Share on other sites
  • 2 weeks later...
Savage Bliss Proficient

Savage Bliss

Posted
Posted

Well, he's bought an R32 4 door yeah? Then says is thinking of keeping the 4 stud... ?????? Ummm, please correct me if I'm wrong, although I pretty sure I'm not, R32 and any other Skyline onwards have 5 stud. : And then there's talk about GXi's GTE's WTF?????

Link to comment
https://www.sau.com.au/forums/topic/122711-r32-4-door-gte/#findComment-2302075
Share on other sites
funkymonkey Grand Master

funkymonkey

Posted
Posted

what if the car's wheels has lugnut covers?

hehe

R32 GXi = 1.8l dizzy driven CA18i SOHC engine

R32 GTE = 2.0L RB20E SOHC engine

These two were pretty much poverty spec cars, meant to ferry families around on the cheap.

R32 GTS = 2.0L RB20DE DOHC engine

This was the top of the range N/A you could get, still had 4 stud hubs, but had the same drivetrain as the GTSt, which is a lot stronger.

R32 GTSt = 2.0L RB20DET DOHC turbo engine

Turbo version of GTS

R32 GTS4 = 2.0L RB20DET DOHC turbo engine

AWD GTSt, sorta like half a GTR and half a GTSt

and the R32 GTR.

R33 had a similar model structure, although the poverty model was only available as an RB20E.

Link to comment
https://www.sau.com.au/forums/topic/122711-r32-4-door-gte/#findComment-2303089
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...