Jump to content
SAU Community

Recommended Posts

:P Hi guys where abouts on the south coast of NSW can i get a Apexi Power FC tuned, don't wanna buy one if i've gotta trailer it a million miles. Cheers

Hi mate i am from sydney and have the same computer if you want to buy it get it installed and dyno'd at one place check out this site its in sydney

www.uniqueautosports.com

Link to comment
https://www.sau.com.au/forums/topic/122962-power-fc-tuning/#findComment-2277504
Share on other sites

CRD, Unigroup engineering, SAS Automotive have all good really good reps, but are in syd. Shouldn't have to get it trailered, either run with stock ecu to shop then plug in, or base maps should be fine to get it there i thought.

http://www.croydonracingdevelopments.com/about_us.htm

http://www.unigroup.com.au/

Link to comment
https://www.sau.com.au/forums/topic/122962-power-fc-tuning/#findComment-2280910
Share on other sites

  • 4 years later...
:P Hi guys where abouts on the south coast of NSW can i get a Apexi Power FC tuned, don't wanna buy one if i've gotta trailer it a million miles. Cheers

What mods have you done, if they are basic then just plug it in and drive the car to the tuner, just don't flog the ass out of it.

Or buy it and drive to your with it in its box and swap it out at the Tuner.

In Canberra I would reccomend ESP Racing or Auto-Tech.

Or In Sydney go to Uni-Group

Link to comment
https://www.sau.com.au/forums/topic/122962-power-fc-tuning/#findComment-5519541
Share on other sites

I have used Screaming Performance in Fairy Meadow with good success in the past. Daryl, the owner, is very switched on - however the workshop I think reflects his mind - quite dirty :)

Link to comment
https://www.sau.com.au/forums/topic/122962-power-fc-tuning/#findComment-5519688
Share on other sites

I've left this open up until now because you're out of the general Sydney CBD, but now that you've got a few answers I'll close it.

Anyone else:

http://www.skylinesaustralia.com/forums/Re...er-t228238.html

Link to comment
https://www.sau.com.au/forums/topic/122962-power-fc-tuning/#findComment-5520236
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...