Jump to content
SAU Community

Lost Boost, No Power!

Trav33

By Trav33,
in Engines & Forced Induction

 Share

Recommended Posts

Trav33 Mentor

Trav33

Posted
Posted

Hi All,

Swapped my turbo on the weekend.

Took it out driving tonight, all was sweet, but then up a hill under power it started missing, so i pulled over and it was running rough, but got smoother after a minute.

Took off again, but now ive got no boost. The stock gauge is going from -7 to -3 under power.

Any ideas what would cause this? Have had a good look under bonnet, nothing looks out of place or missing or noisy...

New turbo = high flowed turbo

R33 Skyline, Mods = the normal Front mount intercooler, exhaust, pod filter

Appreciate any ideas!

Link to comment
https://www.sau.com.au/forums/topic/123058-lost-boost-no-power/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

cooler pipe has come off or youve likely blown an intercooler hose clamp.

put soapy water on the intercooler pipework and look for buggles or check for obvious leaks. if not leeks then exhaust wheel may have failed. do you get an sqeauls or wines when it tries to come on boost ?

Trav33 Mentor

Trav33

Posted
  • Author
Posted

Hey Paul, ta for your reply.

No noises at all when it tries to boost...

I guess it could be a loose intercooler pipe - i had a good look, and felt with my fingers, but you're right that soapy water would be better to detect leaks.

Any other possible causes?

Craved Grand Master

Craved

Posted
Posted

enough of a leak to have no boost would mean that all the air is pumping out of the pipe... unless your running a MAP sensor it wont be that

check the wastegate arm on the turbo from actuator to the wastegate flap.

RANDY Veteran

RANDY

Posted
Posted

Got an aftermarket dump pipe? I had one that smacked up onto the exhaust wheel of the turbo, and didn't let it spin. Possibly the new turbo has a bigger (and metal) wheel, and you have the same thing that I do?

I had no boost and terrible performance, but I did notice a soft whistle sound... prolly the exhaust rushing past the locked up exhaust wheel.

I'd suggest you pull off the intake piping to the turbo, and see if you can manually spin the turbo compressor wheel. This is what my mate told me to do, and how I found out what my problem was.

Trav33 Mentor

Trav33

Posted
  • Author
Posted

Randy,

Good idea... however the turbo did run and the vehicle did drive for a few hours... and the hi-flow turbo is "Bolt-On"... so i doubt it's that...

Hrmm... might have to pull off intake and spin shaft... any other ideas if this is ok? Still have to get some detergent out later today to look for intercooler leaks, but i doubt this is the problem.

png godzilla Enthusiast

png godzilla

Posted
Posted

this is a great method for checking for leaks IC side or Exhaust.

I use Plumbers Test plugs to block the intake (x2) & another one to block the exhaust, just drop it at the cat eliminator pipe (or Cat) & wind it up inside the end of the pipe until it seals.

mines an RB26DETT, with HKS front Pipe so i need 3 x 3" Test plugs.

then you leave all but one blocked & open one only & apply compressed air easilly & straight away you can see where the leaks are either on the pressure side of the IC, the Plenum side & the exhaust!

found out my Intake plenum was leaking on runner # 3 last week. always heard a little whistle from the front, but now i know what it is!!

great trick, worth trying!

post-29939-1150859495.jpg

RANDY Veteran

RANDY

Posted
Posted

If the turbo ran for a while... maybe it wasn't getting oil or something from a blocked pipe? And now it's seized?

Either way, intake stuff off, spin wheel, should tell you if the turbo is even working. For it to have no boost, you'd have to have an entire intercooler pipe completely off or something. The plumbers test sounds like a good diagnostics thing... but i'd personally do that after checking the easy stuff first.

BezerkR32 Veteran

BezerkR32

Posted
Posted

Not unusual for oil feed line to block as it has the restrictor in one end. good chance you might have siezed it. it would be a obvious leak for you to have no boost pressure and car would not idle either.

If the turbo ran for a while... maybe it wasn't getting oil or something from a blocked pipe? And now it's seized?

Either way, intake stuff off, spin wheel, should tell you if the turbo is even working. For it to have no boost, you'd have to have an entire intercooler pipe completely off or something. The plumbers test sounds like a good diagnostics thing... but i'd personally do that after checking the easy stuff first.

RANDY Veteran

RANDY

Posted
Posted

damn man... that's not good news.

For the reasoning, see bezerk's post... and mine above...

Possibly it had no oil, so it just overheated and locked up.

Still, rule everything else out first. Does your dump pipe have that little pipe that bangs up against the exhaust port on the turbo? If so, drop the dump off and try spinning the turbo. If it still doesn't spin, then you can be pretty sure that nothing else is holding the shaft in place.

Maybe talk to the place that did the highflow and get them to check the turbo out... maybe they botched something, or maybe they can prove conclusively that it was due to your installation.

Good luck!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      Can u check this way it works for power supply?
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      These coils draw 10amps that what i read online
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
    • DannyDee2
      First time owner v35

      By DannyDee2 · Posted

      Welcome mate!
×
×
  • Create New...