Jump to content
SAU Community

Coolant Leaking

Fixxxer

By Fixxxer,
in General Maintenance

 Share

Recommended Posts

Fixxxer Community Regular

Fixxxer

Posted
Posted

Hi everyone,

Over the past few months I've noticed on the odd occasion that there is sometimes a little pool of coolant under the car (near the front of the engine). Just recently (the last 4 times I've started the car) the temperature gauge has sat under the C mark (where it normally sits when cold) for about the first 5-10mins of driving, then suddenly will move up quickly to the middle of the gauge where it normally sits. Usually the engine comes up to temperature slowly as is usual in all cars.

Is the gauge shooting up fast a bad thing?? Is it associated with my off and on leak sometimes? Is a new water pump in order??

My car has done 165,000 k's, doesn't get hot (always stays in the middle of the gauge).

Fixxxer >_<

Link to comment
https://www.sau.com.au/forums/topic/123118-coolant-leaking/
Share on other sites
SECURITY Grand Master

SECURITY

Posted
Posted

if it hasnt had a water pump change then do it anyway, i'd get your thermostat changed too.. it should warm up gradually.

check for leaks on the bottom of the water pump, its where they usually leak. if you run your finger under there and find some residue then its time for a pump change.

Link to comment
https://www.sau.com.au/forums/topic/123118-coolant-leaking/#findComment-2274017
Share on other sites
  • 2 weeks later...
Fry_33 Proficient

Fry_33

Posted
Posted

I agree with Joe.

I'm fairly sure that a pool of water, if not from hoses is the sign of a worn out water pump. Nissan makes it this way. It wears past a seal or something sacrificial, can't remember exactly how it works, but it is telling you that it will soon fail. It drips out from a small hole in the housing of the water pump (I think) you might be able to see it. This is what happened with my mates car.

If you do need to change it and haven't done your timing belt yet then you may want to change it at the same time also and save labour costs later on.

Good Luck

Link to comment
https://www.sau.com.au/forums/topic/123118-coolant-leaking/#findComment-2296619
Share on other sites
cowie165 Veteran

cowie165

Posted
Posted

It may also be worthwhile having your radiator pressure tested.

Two weeks ago I had a similar problem with our other car. It was dripping fluid reasonably slowly but left a pool of coolant when I stopped (after first noticing).

I pulled the radiator out - the hoses were in good shape so I had the radiator tested. One of the end tanks had a hairline crack and coolant was leaking out. Bizarrely, it wasn't doing it all the time either. Might be worth a look.

Have you checked your coolant level in the radiator (not the overflow reservoir) as the rapid temp rise may not be a faulty thermostat. If your coolant level is low, once the thermostat begins to open, there may such a low volume of coolant in the block/radiator that it heats very quickly, yet there is enough to maintain safe operating temp.

Think about how quickly the kettle boils when there is only a little water inside compared to when it is full. Assume the engine is the kettle element - it is a constant source of heat and the smaller volume means it will heat quicker.

I'm not saying it is one way or the other, but thought it was something to consider.

Link to comment
https://www.sau.com.au/forums/topic/123118-coolant-leaking/#findComment-2300274
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Airbox for +T

      By Kinkstaah · Posted

      It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • GTSBoy
      Airbox for +T

      By GTSBoy · Posted

      By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • BuiltNotBought
      Airbox for +T

      By BuiltNotBought · Posted

      There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
    • BuiltNotBought
      Airbox for +T

      By BuiltNotBought · Posted

      I haven’t yet cut the chassis, maybe I switch to a reverse flow. I’ve got the Intercooler mounted as I already had it but not cut yet. Might have to speak to an engineer 
    • BuiltNotBought
      Airbox for +T

      By BuiltNotBought · Posted

      Yes that’s another issue, I always have a front mount, plus will be turbo plus intake will big hasstle. I’ve been told if it looks stock they’re fine with it by a couple others who have done it ahahaha.    I know @Kinkstaah said the stock gtt airbox is limiting but I might just have to do that to avoid a defect so it atleast looks legit. Or an enclosed pod so it’s hidden away and feed air from the snorkel and below Intercooler holes like kinstaah mentioned. Hmm what to do 
×
×
  • Create New...