Jump to content
SAU Community

Recommended Posts

Hi guys,

Passenger window of my SII R33 got broken a few days ago - since happening the door is stuck locked; can't move the switch by hand, and when using central locking I can hear the motor whining but it doesn't actually unlock. I'm guessing that some of the broken glass has fallen inside the door and is blocking the unlock mechanism.

Wondering how hard you guys think it would be to fix myself? Bearing in mind that I've only had the car a week or so and haven't forayed into the realm of DIY much in the past... I assume I could get it done while the window is getting replaced, but since I'm waiting on one to come from Japan (already sorted) that won't be happening for a couple of weeks and I'd like to get the door operational before that.

Opinions? Anything I could easily mess up by trying? I'd rather not cause more damage thru my incompetence! I also assume I'd have to take off the door trim; haven't done this before, had a quick search and saw a tutorial for R32 that didn't seem to match up with my R33, advice? Will I even be able to take it off with the door still closed?? Cheers.

Link to comment
https://www.sau.com.au/forums/topic/123187-r33-locking-mechanism/
Share on other sites

If you get a torch and a coat hanger with a 10-20mm hook on the end you will see near the lock mech on the inside, a lever with the door handles rod thingos, jiggle that about for a while, it may loosen it, with the door closed ALL the ingress points are blocked

thats gonna be very nasty

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...