Jump to content
SAU Community

Recommended Posts

  • Replies 108
  • Created
  • Last Reply

Top Posters In This Topic

Installed the pipe on weekend, took about 4hrs, mostly just spraying the rusted bolts with rp7 and waiting around for it to work its magic. A couple of questions though, did anyone else notice that if you give it some it seems to over boost? on the drive to work this morning i put the foot down about half way to work (gives it about a 10min warm up) then a soon as the auto kicked back the turbo spool was a hell of alot louder than before and boost shot up to just below the 1+ line (didn't hear anything rattle down the exhaust pipe though, thank god), normal? should i be concerned?

Installed the pipe on weekend, took about 4hrs, mostly just spraying the rusted bolts with rp7 and waiting around for it to work its magic. A couple of questions though, did anyone else notice that if you give it some it seems to over boost? on the drive to work this morning i put the foot down about half way to work (gives it about a 10min warm up) then a soon as the auto kicked back the turbo spool was a hell of alot louder than before and boost shot up to just below the 1+ line (didn't hear anything rattle down the exhaust pipe though, thank god), normal? should i be concerned?

i've heard that you'll get an extra few psi of boost because of the lack of restriction in the exhaust. I wouldn't worry about it, whats it set to normally? Or is it stock boost?

yeah stock boost; still using the stock cat and system after the dump, the power gain seem to be noticable as well, turbos alot noiser now though.

I suggest you get a boost guage now. Just to monitor and be safe.

Yup i noticed the difference immediately. Spools up much quicker, sounds better, more inductions noise, more kick, better sounding car.. what more do you want..

Hmm howd u use your existin gasket?? wouldnt it be to small?

I suggest you get a boost guage now. Just to monitor and be safe.

Yup i noticed the difference immediately. Spools up much quicker, sounds better, more inductions noise, more kick, better sounding car.. what more do you want..

Hmm howd u use your existin gasket?? wouldnt it be to small?

no probs with using the existing gasket, what do you mean by too small?

ohh sorry meant at the end of pipe connecting to hi-flow cat..

I had to use a new gasket for that.. but all good!!

yea i just used the orginal gasket, still was in good nick; getting the rest of system done soon so its going to be replaced anyway.

installed mine

took about 4 hours.....pretty much bolt on...some very minor adjustments to mine

turbo spools early...goes harder throughout the whole rev range and very responsive compared to stock

great product

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...