Jump to content
SAU Community

Recommended Posts

Group buy for Braided master to slave cylinder clutch lines.

These replace all the piping and the junction block and the factory rubber hose.

Similar to this:

Nissan%20Clutch%20Ass%20Braided.JPG

Replaces all the piping as in this pic:

Nissan%20Clutch%20Ass.JPG

Product:

- Replacement stainless clutch line.

- ADR approved.

- Manufactured by MALTECH.

- Available for R32 GTST, R33 GTST, R34 GTT, R32 GTR, R33 GTR, R34 GTR, WGNC34.

- Insert Colours - red, blue, smoked, black.

- Plastic coating is also avaialble (for same price) - red, blue, black, clear.

Inserts%20Coated%20Colours.JPG

Prices:

5 buyers:

R32 GTST - R33 GTST - $85.00each (rrp- $90.00each)

R34 GTT - R32 GTR - R33 GTR - R34 GTR - $90.00each (rrp- $95.00each)

STAGEA RS4 Series 1 (manual conversion) - $85.00each (rrp- $90.00each)

STAGEA RS4 Series 2 - $90.00 each (rrp- $95.00each)

10 buyers:

R32 GTST - R33 GTST - $80.00each (rrp- $90.00each)

R34 GTT - R32 GTR - R33 GTR - R34 GTR - $85.00 each (rrp- $95.00each)

STAGEA RS4 Series 1 (manual conversion) - $80.00each (rrp- $90.00each)

STAGEA RS4 Series 2 - $85.00 each (rrp- $95.00each)

Also available- 180SX - S13 - S14 - S15 (rrp- $90.00each)

Postage (1-2 sets) - $7.50 express within Australia.

Finish date - 28/09/06

Payment due - 01/10/06

1/ IMPUL R32-R - R32 GTST - blue inserts - clear coating

2/ willsy - R32 GTSt - black inserts - clear coating

3/ darrinspencer - stagea - black inserts - smoked coating

4/ boss33 - R33 GTST - blue inserts - blue coating

5/ private buyer

6/ clincha - R32 GTST - blue inserts - clear coating

7/

8/

9/

10/

:(

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

I need a odd one

R34 GTT master cyclinder

R33 GTR slave cylinder

Length to suit a Stagea, should be the same as a R34GTT

Smoked hose, black ends

I need a odd one

R34 GTT master cyclinder

R33 GTR slave cylinder

Length to suit a Stagea, should be the same as a R34GTT

Smoked hose, black ends

No probs. Its available and is the same price as the R34 GTT line.

Shall I add you to the list?

:)

ALSO AVAILABLE:

STAGEA RS4 Series 1 - $75.00each (rrp- $90.00each)

STAGEA RS4 Series 2 - CAN ANY ONE CONFIRM IF THE SERIES 2 MASTER TO SLAVE IS THE SAME AS THE SERIES 1??

ALSO AVAILABLE:

STAGEA RS4 Series 1 - $75.00each (rrp- $90.00each)

STAGEA RS4 Series 2 - CAN ANY ONE CONFIRM IF THE SERIES 2 MASTER TO SLAVE IS THE SAME AS THE SERIES 1??

Series 1 Stagea only ever came out as a auto from the factory except Autech 260RS Rb26dett

Series 2 Stagea came as a factory manual or tiptronic auto

Yes I want one

My car is a series 2 auto that I am converting to manual

Hope that clears things up

My line arrived today in the post (I ordered it directly from Maltech, wasnt aware of this groupbuy).

Great looking line and excellent service from Maltech.

My line arrived today in the post (I ordered it directly from Maltech, wasnt aware of this groupbuy).

Great looking line and excellent service from Maltech.

Greddy,

can you get the ones from maltech that just replace the rubber section of the pipe? I dont want a braided line like in your first pic, i want one that just replaces the rubber section in the second pic.

Thanks mate!

Greddy,

can you get the ones from maltech that just replace the rubber section of the pipe? I dont want a braided line like in your first pic, i want one that just replaces the rubber section in the second pic.

Thanks mate!

PM sent :D

is this group buy still going? im interested in getting a braided clutch line for my gtt

This group buy is still going.

Finish date - 10/07/06

Payment due - 15/07/06

Shall I add you in?

:whistling:

anyone else?

I need more buyers to offer them for the good price.

:blink:

Put me in for a stainless one for gtr33

Smoke clear coated

Thanks

Is this still going ahead?

  • 4 weeks later...



  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...