Jump to content
SAU Community

Recommended Posts

Hi guys.

First time posting in this particular forum - been told we speak a different language in the stagea forums so bear with me.

Im looking to upgrade the R31 sitting in my garage. Was a 31 silhouette. (still is).

Ive ben told you can use s13 control arms and steering, as well as coilovers to suit s13s. Do r32 parts fit, even?

What other later model steering/suspension components can you transplant to update the handling of a 31?

The car has the RB30DE in it, which is either going to get a VL turbo kit, or just a whole new engine. (probably a cheaper option.)

Would appreciate it if you could sling me some ideas.

Note - this car will not be registered, will be something to practise drifting, so that when i clean something up i can fix it easy enough.

Also if anyone is SELLING a 31, let me know, cos id love to have another one. 5spd a must. Thank you!

Link to comment
https://www.sau.com.au/forums/topic/125844-uprages-to-r31-4drs-howd-you-do-it/
Share on other sites

If you have a DE then sell it to me - I'll exchange my rb30e for it. Noisy lifters and leaky cover but otherwise seems ok and put out a healthy 101rwkw on the dyno my cefiro put out 180rwkw on :P

s13 lower control arms, hubs, rotors, calipers, brake lines and a few bolts (m8 and/or m10, m12 high tensile) and you can do the front.

For the rear if you don't care you can just "bolt in" the coilovers but you'll need to drill new holes in the tray for the coilovers to sit as they have a different bolt pattern. I'm trying to keep my car engineerable so I bought some hats that will allow the coilovers bolt into the stock holes.

You'll also want to get coilovers that are high on a s13, or are adjustable because apperantly at the highest setting it's still low on the r31 so most of the r31 guys, from what I understand, run around on the highest setting.

^^^ I'm just regurgitating from the r31skylineclub and you can check em out there, altho their wiki section is a good start is missing often important but little things :laugh:

I've got all the parts and will probably be adding to the wiki or doing my own tut for SAU when I get around to putting the parts in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...