Jump to content
SAU Community

Recommended Posts

I know this is a skyline appreciation forum but i have always been open minded about cars. If the XR6t had been around when i bought my GTS25t i would have had a much more difficult time deciding on buying my skyline.

In the following link they say that with a couple of tweaks and some extra boost you get 252rwkw out of the XR6t. How tuff is that. Also they say that 300rwkw would be a "doddle", that will really put the wind up someone driving a HSV with 300 flywheel kw.....

http://www.fordforums.com/showthread.php?t...25&pagenumber=1

I think it is impressive that a local manufacturer has finally come up with a MODERN performance car. None of this single cam push rod junk but a really serious peice of gear. Mind you dont get me started on how the intercooler is plumbed because that really was a MAJOR COMPROMISE.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/
Share on other sites

bolting on a turbo doesn't instantly makes it a well refine sportcar as a skyline. but it does help the falcon street cred though. if u get a chance hurl one into a sweeper at the same rate as u would do in a skyline and see how much room there is left in ur undies. It's still a family car in the end.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-230877
Share on other sites

Hungry 6 have you tried driving one????

It is more of a family car than a race car (skyline being a race car of course) as such it will weigh more.

I personally hate the way the intercooler/ inlet manifold/ turbo is piped because it is a compromise. BUT you cant argue with a family car that pulls 240kW running 6psi which is heavily detuned. Oh by the way can your car seat 4 people as comfortably as a XR6t???

I took one for a run and i was surprised at how the suspension combined with the traction control made the car stick under serious accelaration through some cornering. The sales person did get a bit edgy at times but i assured him that i was looking at upgrading from the GTS25t to a family car with some go (cough cough like hell i was).

They didnt JUST bolt on a turbo if you check the specs they also dropped the static compression ratio and did a lot of heat shielding among other things.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-230969
Share on other sites

My mate works for the company that makes Ford's transmissions, and agrees the manual is at an end for torque handling, they have been leaning on it for years and keep asking to do what it was never designed to do, with this in mind the 5 spod doesnt do that bad a job.

He has worked primarily on the auto, and with him having driven my 32 GTST many times when im pissed and egging him on, he has a good idea what my car can do.

For the record the guy isnt full of BS, and claims despite the weight of the car, and saloon heritage, the development mules that he R & D flog my GTSt in accelaration, have great brakes, and handle great. He says with the handling you just have to be mindful the it is a production car with a pretty hefty kerb weight, so no brakes/heavy acceleration mid corner/ebtry to corner etc, be smooth and it can do the job. Hell he has driven the thing on great ocean road.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-231153
Share on other sites

I've heard from a few sources that the XR6t has a boost limit of 7psi.

Once it hit's 7psi the ECU starts to pull back timing and then starts the boost cut - just like some R33 gts-t's hit at 12psi.

If this is true, it'd be a pain in the butt to go to a full ECU change on such a modern car for a few extra psi :D

They are nice cars though. Boss at work has a blue one... Nice......

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-231353
Share on other sites

There was a good article in the last HPI comparing the XR6 Turbo to the Supra. They said "The closest thing to a Japanese car to come out of Australia. We can't praise the XR6T any more than that".

I think the guy doing the review was a little biased as he owns a Supra, but hey, what can you do?

The writer goes on about how the 2JZ-GTE is the greatest and most proven engine of all time, whereas the 240T still has to prove it's self. "The few players in the aftermarket who have tested the 240T engine have come away confused and frustrated with an uncooperative managment system, and intercooler/exhaust systems that are far from optimum".

Apparently the LPG spec rods are a must for a serious build-up.

They also said that the Ford doesn't like to be revved!

All in all though, I think Ford is onto a good thing. However, if I was looking for a sporty family car, I'd still by a WRX!

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-232077
Share on other sites

OK

Firstly it is a 4ltr. Motors with large swept capacity dont need to rev much because the have bulk torque early on in the rev range where as my RB25DET needs to be revved to get any go out of it.

For a sporty family car i would think it is ideal because you get a large turbo six with auto. You can be as lazy as you want to be and you can seat 4 passengers with large arses comfortably.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-232092
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...