Jump to content
SAU Community

Recommended Posts

Anyone got any idea what might have cause these failures? The gudeon pins have snapped in two. The same thing happened in two different engines. Both CA18DETs (similar to RB but 4 pot rather than 6), both using Wiseco pistons, both failed in only 100kms.

Its a strange one as I know of lots of people using Wisecos in CAs with no problems and yet this one guy has two identical failures. Any idea what he is doing wrong?

1.6.06%20joo%20020%20(Small)(1).jpg

IMG_2311%20(Medium).JPG

IMG_2314%20(Medium).JPG

Link to comment
https://www.sau.com.au/forums/topic/126195-strange-pistongudgeon-pin-failure/
Share on other sites

piston is not fauling on crankshaft counterweight is it, or crankshaft have excessive endfloat? unless pin is grabbing little end and piston, lubrication problem. never seen anything like it, thats big.

Anyone got any idea what might have cause these failures? The gudeon pins have snapped in two. The same thing happened in two different engines. Both CA18DETs (similar to RB but 4 pot rather than 6), both using Wiseco pistons, both failed in only 100kms.

Its a strange one as I know of lots of people using Wisecos in CAs with no problems and yet this one guy has two identical failures. Any idea what he is doing wrong?

1.6.06%20joo%20020%20(Small)(1).jpg

IMG_2311%20(Medium).JPG

IMG_2314%20(Medium).JPG

Those are the only pics I have Im afraid. Its a guy in another country thats having probs, I havent been involved with the build myself. The pistons are nothing out of the ordinary, as I say, they have been used with great sucess in a large number of engines to date so I cant see why they would suddenly foul on the crank. I can see maybe one set of pistons being mispacked by Wiseco but two, and both sets going to the same guy? Nah, too much of a coincidence.

Maybe the piston to bore clearance isnt correct and the pistons nipped up when the engines got hot but to snap the gudgeon pics? Ive seen the effects of hydraulic locking and even then it was the rods that bent, not the gudgeon pins snapping.

Very wierd.

Edited by bren

I've seen it before in a V10 Viper and it was a detonation issue. It broke 2 gudegeons and had 4 more cracked ones.

That was a brand new engine with Wiseco's. It was rebuilt and retuned (the right way!) and it's never had anothe problem since, even with the same pistons.

I tend to think that the gudgeon pin tried to sieze in the small end bush . You can see how the bush has tried to screw itself out of the rod and no doubt up against the inside of the pistons gudgeon pin boss . Since both pins are sheared in the middle it seems logical that half the pin was trying to stop the piston articulating with the rod and was the weakest link . Luckily the other half must have kept the small end located in the piston otherwise the rods and pistons would now be schrapnell on the road . I would be measuring up the broken and surviving pins to see if the tolerances were adequate .

I would also check to see if the propper lubrication was available to all four rods/pins/pistons .

Cheers .

Edited by discopotato03

ok. the only thing that causes a gudion pin failer is either a clerance issue or fauly materials. (dodgy gudion pin)

the fact that it shered could be due to the fact that its been hammering away at its self. elongating the piston pin bore and/or hammering the bush in the conrod.

to a point where it has hammerd it so hard that its fractured the gudion pin.

or.. partaly siezing in the pin boss or little end. ie.. one side getting galled andthe othere side being ok.

so basicly the cause is to little or two much clearance inbetween the piston and the gudion pin or two much clearance between the gudion pin and smallend bushing :D

ie.. poor engine assembly.

ps... if anyone for a minute thinks that detonation has caused this please slap yoursefl ;)

ok. the only thing that causes a gudion pin failer is either a clerance issue or fauly materials. (dodgy gudion pin)

the fact that it shered could be due to the fact that its been hammering away at its self. elongating the piston pin bore and/or hammering the bush in the conrod.

to a point where it has hammerd it so hard that its fractured the gudion pin.

or.. partaly siezing in the pin boss or little end. ie.. one side getting galled andthe othere side being ok.

so basicly the cause is to little or two much clearance inbetween the piston and the gudion pin or two much clearance between the gudion pin and smallend bushing :D

ie.. poor engine assembly.

ps... if anyone for a minute thinks that detonation has caused this please slap yoursefl ;)

I'm with you on this one, detonation isn't going to do this. I would still like to see the big ends as they will probably show more of the story. If the little end is hammer the big end certainly is going to be showing signs of abuse as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers)
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
×
×
  • Create New...