Jump to content
SAU Community

R34 Project About To Start

drgnball34

By drgnball34,
in Engines & Forced Induction

 Share

Recommended Posts

drgnball34 Rising Star

drgnball34

Posted
Posted

My turbo finally arrived. Its a Gt3071RR .82 A/R coupled with high mount and tial gate. Other supportings mods are tomei Fuel pump, Nismo 480cc injectors, Sard regulator, tomei cams, Power fc etc.. It seems to me that the L pipe that has the factory BOV attached just before the intake manifold will casue a problem when installing my turbo and highmount. I think it's slighty bigger then the R33's. That means it will need to be removed and have custom piping done which I need anyways. My question is if the standard intercooler piping which runs across the engine bay can no longer be used, how would i go about fabricating a new desgin?. I've seen a few R33 designs where the piping runs from the intercooler and up and around the top of the engine. But on the NEO i dont think thats possible because the layout is abit different and very limited space. Correct me if im wrong. My other option is the Greddy plenum but i heard that is doesnt fit the Neo engine. Any idea what needs to be done to make it fit? Or is there another way around this?

Link to comment
https://www.sau.com.au/forums/topic/126360-r34-project-about-to-start/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What brakes on R34 GTT(Europe)

      By Dose Pipe Sutututu · Posted

      Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...