Jump to content
SAU Community

Recommended Posts

post-29018-1165659286.jpgpost-29018-1165659265.jpgpost-29018-1165659240.jpgpost-29018-1165659196.jpgpost-29018-1165659167.jpgpost-29018-1165659111.jpgpost-29018-1165659046.jpg[attachmen

=71103:attachment]post-29018-1165658996.jpgpost-29018-1165658968.jpg[att

chment=71099:attachment]post-29018-1165658910.jpgpost-29018-1165658885.jpgpost-29018-1165658853.jpgpost-29018-1165658541.jpgpost-29018-1165658563.jpgpost-29018-1165658599.jpgpost-29018-1165658633.jpgpost-18675-1123468605.jpgpost-29018-1165658500.jpgpost-29018-1165658680.jpg[attachme

t=71091:attachment]post-29018-1165658818.jpghi there.. selling my white r33 skyline.. details are...

car: nissan skyline r33 gtst 95' coupe

LOCATION: Sydney

Kilometres reading: 97.000kms

price: $14500

REASON FOR SELLING: lost license :)

CONDITION: Good Condition

DETAILS:

CONTACT: [email protected] or 0410957457 anytime

BODY:

body is white with stickers on the side... Mspec bodykit.. s2 wing cut out front bar for Front mount..

ENGINE + MODS

FMIC with chrome piping

3 inch HKS hi-flow exhaust

blitz air filter

Cold Air intake

GFB blow off valve

Tein adjustable coilover suspension

turbosmart Boost controller with incar flick switch 7psi - 12psi (now sitting at 9 psi, since i bought this car i wound down the Boost controller and never boosted it to 12 psi..)

Brass Button Clutch

18 inch GENUINE WHITE ROH MODENA 3 piece 5 spoke rims with good rubber.. 18 x 9.5 deep dish at rear. Suits the car Hard

Greedy Turbo timer

GTR rear Pods

INTERIOR:

Momo Steering wheel

Isotta gearnob

Momo Handbrake

Pioneer Mp3 player

Autometer Boostgauge with shift light

Info on car:

car has rego until late april 07' runs really smooth and is reguarly tuned with motul oils and platinum spark plugs. also is fitted with an keyless entry/alarm and HID head lights. car looks immaculate and the combination of WHITE body and white rims matches the car perfect. welcome anytime for inspection.

Problems:

dent on top of the drivers door is minor nothing major..

everything else is preety good.. reguarly washed at BMW rushcutters bay..

rami

post-29018-1165658657.jpg

post-29018-1165658719.jpg

post-29018-1165658938.jpg

post-29018-1165659079.jpg

post-29018-1165659134.jpg

Edited by rami
  • 4 weeks later...
  • 4 weeks later...

bump. will consider swap for a boat/jet ski.. loosing my license soon..

and power fc is sold........ its not on the car anymore...

and the cluster is all fixed too... :)

i wana sell this thing already.. im loosing my license and i want a boat ASAP for summer!

  • 1 month later...
  • 3 weeks later...

BUMP.. please someone buy this.... i keep getting done driving it.. its got brand new dunlop sports rubbers on it now... costed a fair bit...! price is negotiable and open for offers for a road bike.. (600cc plus)

  • 2 weeks later...

BUMP! Somebody take this f*kA off me!.. no word of a lie.. ive gotten done 2 times after i lost my license... so im loosing it for even longer! im stupid for driving but the hell with my license.. its a skyline :happy: lol

gimi any close offer.. im selling this car with a brand new turbo as well.. either stock or tr43 turbo if the guy replies soon enough....

cheers

  • 2 weeks later...
  • 2 weeks later...
  • 1 month later...
  • 2 weeks later...
  • 3 weeks later...

bump... im now considering some seriious price drop offers... offer me anything over 12 the car is yours.. its a machine i cant believe no one has interest in it... cmon guys surely someone wants a car sitting on some fkn expensive wheels... roh modenas cost $860 a wheel! no rubber.

performance wise its a freak come check it out no one has nothing to loose.. cant have this car in my driveway anymore.

loox like a nice car champ... if i didnt have 3 cars lying around i would of bout it.. loox like a good buy and uve seen it around.. nice car..

good luck with sale..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...