Jump to content
SAU Community

Recommended Posts

  • Replies 167
  • Created
  • Last Reply

Top Posters In This Topic

I heard a rumour that there were CAMS officials present at the Sandown meet and that they were concerned about the safety of modified GTR's in that the times they are getting, and speeds they are achieving are not far removed from racing/touring cars. They may be considering a ruling that full roll cages are to be fitted to modified GTR's.

Anyone heard anything about this???

Hi Neil,

We (the wrx club) have been approached by CAMS for a sort of informal review on safety. It is fair to say that we attract arguably the fastest club cars in Victoria on a regular basis - even PCV don't manage to field the sort of horsepower that normally appears at Vic WRX club sprints.

It hasn't gone anywhere yet but it certainly wont go away in a hurry.

Watch this space.

Regards

Andrew

While i can understand CAMS being worried about the times some of the cars are putting down, but it would be a shame for them to turn around and force us to have cages, because I for one wouldn't put a cage in my car, which would mean no more track days.... that being said i guess i'd have to go as fast as you guys first... which may never happen.

Better late than never. I'd like to publically thank the Snowman for helping me out on Saturday with a set of his old pads.

I did a Ferni to my brakes, less spectacular, I went out and mirrored this senseless act of destruction on my own car. I won't ever do that again....

Better late than never. I'd like to publically thank the Snowman for helping me out on Saturday with a set of his old pads.

I did a Ferni to my brakes, less spectacular, I went out and mirrored this senseless act of destruction on my own car. I won't ever do that again....

Bwwwhahahaa, Kaching baby.

Better late than never. I'd like to publically thank the Snowman for helping me out on Saturday with a set of his old pads.

I did a Ferni to my brakes, less spectacular, I went out and mirrored this senseless act of destruction on my own car. I won't ever do that again....

Yes but you got a 1.18

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...